Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc b2902 rear height sensor circuit

AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC B2902 REAR HEIGHT SENSOR CIRCUIT

DTC detecting condition:

Detected when error occurs in the rear height sensor.

Trouble symptom:

The auto headlight beam leveler does not operate.

CAUTION:

Initialization is required after replacing the auto headlight beam leveler CM.

Wiring diagram:

Headlight beam leveler system Headlight Beam Leveler System > WIRING DIAGRAM">

STEPCHECKYESNO

1.CHECK DTC.

1) Turn the ignition switch to OFF > ON.

2) Turn on the headlight low beam.

3) Using the Subaru Select Monitor, clear the auto headlight beam leveler system memory. Clear Memory Mode">

4) Turn the ignition switch to OFF > ON.

5) Use the Subaru Select Monitor and read DTCs. Read Diagnostic Trouble Code (DTC)">

Is DTC B2902 displayed? (current malfunction)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2902 REAR HEIGHT SENSOR CIRCUIT">Go to Step 2.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.CHECK CURRENT DATA.

Display «R Sensor Signal» using Subaru Select Monitor. Read Current Data">

Does the data indicate the standard value (approx. 2.5 V when on a level road with one person in the vehicle)?

Replace the auto headlight beam leveler CM. Auto Headlight Beam Leveler Control Module">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2902 REAR HEIGHT SENSOR CIRCUIT">Go to Step 3.

3.CHECK CURRENT DATA.

1) Display «R Sensor Signal» using Subaru Select Monitor. Read Current Data">

2) Change the vehicle posture.

Does the data change?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2902 REAR HEIGHT SENSOR CIRCUIT">Go to Step 6.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2902 REAR HEIGHT SENSOR CIRCUIT">Go to Step 4.

4.CHECK OUTPUT VOLTAGE BETWEEN AUTO HEADLIGHT BEAM LEVELER CM AND VEHICLE HEIGHT SENSOR.

1) Disconnect the vehicle height sensor connector.

2) Turn the ignition switch to ON.

3) Measure the voltage between the vehicle height sensor connector and chassis ground.

Connector & terminal

(R29) No. 3 (+) — Chassis ground (−):

Is the voltage 5±0.25 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2902 REAR HEIGHT SENSOR CIRCUIT">Go to Step 5.

Replace the auto headlight beam leveler CM. Auto Headlight Beam Leveler Control Module">

5.CHECK REAR HEIGHT SENSOR.

1) Remove the rear vehicle height sensor.

2) Perform the inspection of rear height sensor unit. Rear Height Sensor > INSPECTION">

Is the rear height sensor normal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2902 REAR HEIGHT SENSOR CIRCUIT">Go to Step 6.

Replace the rear height sensor. Rear Height Sensor">

6.CHECK HARNESS (OPEN CIRCUIT).

1) Disconnect the auto headlight beam leveler CM connector.

2) Using a tester, measure the resistance between the auto headlight beam leveler CM connector and rear height sensor connector.

Connector & terminal

(B150) No. 3 — (R29) No. 1:

(B150) No. 19 — (R29) No. 2:

(B150) No. 12 — (R29) No. 3:

Is there continuity?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2902 REAR HEIGHT SENSOR CIRCUIT">Go to Step 7.

Repair or replace the open circuit of harness.

7.CHECK HARNESS (GROUND SHORT CIRCUIT).

Using a tester, measure the resistance between the auto headlight beam leveler CM connector and chassis ground.

Connector & terminal

(B150) No. 3 — Chassis ground:

(B150) No. 19 — Chassis ground:

(B150) No. 12 — Chassis ground:

Is the resistance 10 k? or more?

Replace the auto headlight beam leveler CM. Auto Headlight Beam Leveler Control Module">

Repair or replace the short circuit of the harness.

Dtc b2900 ahl control
AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2900 AHL CONTROLDTC DETECTING CONDITION:Detected when internal malfunction occurs in t ...

Dtc u0073 control module communication bus off
AUTO HEADLIGHT BEAM LEVELER SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0073 CONTROL MODULE COMMUNICATION BUS OFFDetected when CAN line abnormality is detecte ...

Other materials:

Dtc u0151 lost communication with restraints control module
INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0151 LOST COMMUNICATION WITH RESTRAINTS CONTROL MODULEDetected when CAN data is not received from airbag CM.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Procedure > PROCEDURE ...

Component
AIRBAG SYSTEM > General DescriptionCOMPONENT(1)Front sub sensor RH(4)Airbag warning light (in combination meter)(7)Airbag control module(2)Front sub sensor LH(5)Airbag ON/OFF indicator light (MFD)(8)Knee airbag module(3)Driver’s airbag module(6)Passenger’s airbag module(9)Steering rol ...

Dtc c0054 bls on malfunction
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C0054 BLS ON MALFUNCTIONDTC detecting condition:Defective stop light switchTrouble symptom:• VDC does not operate.• EyeSight does not operate.Wiring diagram:Vehicle dynamics contr ...

© 2016-2022 Copyright www.sucross.com