Subaru Crosstrek Service Manual: Dtc b28b7 ldp off switch
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC B28B7 LDP OFF SWITCH
Detected when lane departure warning OFF switch circuit is not installed, open-circuited, or is stuck to ON.
DTC detecting condition:
• Wiring of lane departure warning OFF switch is not connected.
• Lane departure warning OFF switch circuit is open.
• Lane departure warning OFF switch circuit stays ON for 45 seconds or more.
Trouble symptom:
All functions of EyeSight system do not operate.
Wiring diagram:
EyeSight System EyeSight System > WIRING DIAGRAM">
| STEP | CHECK | YES | NO |
1.CHECK CURRENT DATA.
Confirm the current data «Lane Departure OFF SW (BIU)» of EyeSight using Subaru Select Monitor. Read Current Data">
Does the display change according to the lane departure warning OFF switch ON/OFF operation?
Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE:
In this case, temporary poor contact of connector, or temporary open or short circuit of harness may be the cause.
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B28B7 LDP OFF SWITCH">Go to Step 2.
2.CHECK HARNESS.
1) Disconnect the stereo camera connector and the lane departure warning OFF switch connector.
2) Using the tester, measure the resistance between the stereo camera connector and lane departure warning OFF switch connector as well as chassis ground.
Connector & terminal
(R406) No. 4 — (R137) No. 13:
(R406) No. 5 — Chassis ground:
Is the resistance less than 1 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B28B7 LDP OFF SWITCH">Go to Step 3.
Repair or replace an open circuit in harness between the stereo camera connector and lane departure warning OFF switch connector.
3.CHECK HARNESS.
Using the tester, measure the resistance between the lane departure warning OFF switch connector and chassis ground.
Connector & terminal
(R406) No. 4 — Chassis ground:
Is the resistance 1 M? or more?
Check the lane departure warning OFF switch. Switches and Harness > INSPECTION">
Repair or replace the short circuit to ground in harness between the stereo camera connector and lane departure warning OFF switch connector.
Dtc b28b6 pre-collision off switch
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28B6 PRE-COLLISION OFF SWITCHDetected when pre-collision brake OFF switch circuit is not installed, open-circuit ...
Dtc b28b8 eyesight steering switch 1
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28B8 EyeSight STEERING SWITCH 1Detected when EyeSight steering switch is not installed or has malfunction, or wh ...
Other materials:
Dtc u0122 lost communication with vehicle dynamics control module
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0122 LOST COMMUNICATION WITH VEHICLE DYNAMICS CONTROL MODULEDetected when CAN data from VDC is not transmitted to stereo camera.When lost communication with vehicle dynamics control and vehicle dynamics control m ...
Inspection
ENTERTAINMENT > Switches and HarnessINSPECTION1. SATELLITE SWITCH ASSEMBLY1. Measure the resistance between connector terminals.Preparation tool:Circuit testerTerminal No.Inspection conditionsStandard6 — 2VOL (+)VOL (−)SEEK (›)SEEK (‹)LISTRETURNA circuit is all OFF.Approx. 1 ...
Installation
BRAKE > Front Disc Brake AssemblyINSTALLATIONNOTE:Before installation, remove mud and foreign matter from the caliper body assembly and support - front disc brake.1. Check each part. Front Disc Brake Assembly > INSPECTION">2. Apply a thin coat of grease to the support - front disc bra ...
