Subaru Crosstrek Service Manual: Dtc b27a8 trunk/rear gate external antenna open

DTC detecting condition:

When open circuit occurs in the harness between keyless access CM and rear exterior antenna.

Trouble symptom:

Keyless access system does not function.

(Unable to unlock with the rear gate opener button, or unable to lock with the rear lock button.)

CAUTION:

For replacement procedure of keyless access CM, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

1.CHECK LAN SYSTEM.

Inspect LAN system. Basic Diagnostic Procedure > PROCEDURE">

Is LAN system normal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A8 TRUNK/REAR GATE EXTERNAL ANTENNA OPEN">Go to Step 2.

Perform the inspection according to the diagnosis for LAN system.

2.CHECK CONNECTOR.

1) Disconnect the keyless access CM connector.

2) Disconnect the rear exterior antenna connector.

Is the connector OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A8 TRUNK/REAR GATE EXTERNAL ANTENNA OPEN">Go to Step 3.

Repair or replace the connector.

3.CHECK HARNESS (OPEN CIRCUIT).

Using a tester, measure the resistance between the keyless access CM connector and rear exterior antenna connector, and between rear exterior antenna connector and chassis ground.

Connector & terminal

(B573) No. 2 — (R299) No. 1:
(B573) No. 1 — (R299) No. 2:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A8 TRUNK/REAR GATE EXTERNAL ANTENNA OPEN">Go to Step 4.

Repair or replace the open circuit of harness.

4.CHECK HARNESS (GROUND SHORT CIRCUIT).

Using a tester, measure the resistance between the keyless access CM connector and chassis ground.

Connector & terminal

(B573) No. 2 — Chassis ground:
(B573) No. 1 — Chassis ground:

Is the resistance 10 k? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A8 TRUNK/REAR GATE EXTERNAL ANTENNA OPEN">Go to Step 5.

Repair or replace the short circuit of the harness.

5.CHECK DTC.

1) Connect the keyless access CM connector.

2) Using the Subaru Select Monitor, clear the memory. Clear Memory Mode">

3) Read DTC using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is DTC B27A8 displayed?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A8 TRUNK/REAR GATE EXTERNAL ANTENNA OPEN">Go to Step 6.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

6.CHECK KEYLESS ACCESS CM.

1) Replace the rear exterior antenna with the rear interior antenna. Keyless Access Indoor Antenna"> Keyless Access Outdoor Antenna">

2) Using the Subaru Select Monitor, clear the memory. Clear Memory Mode">

3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is DTC B27A8 displayed?

Replace the keyless access CM. Keyless Access CM">

Malfunction occurred in the rear external antenna.

Dtc b27a7 trunk/rear gate internal antenna open

Dtc b1572 imm circuit except antenna circuit

Other materials:

Inspection
SECURITY AND LOCKS > Keyless Entry SystemINSPECTION1. SYMPTOM CHARTSymptomsRepair orderReferenceNone of the functions of the keyless entry system operate.1. Check the keyless transmitter battery. Keyless Entry System > INSPECTION">2. Remove and visually inspect the following fuses.&bul ...

SRS airbag system servicing
WARNING When discarding an airbag module or scrapping the entire vehicle damaged by a collision, consult your SUBARU dealer. The SRS airbag has no userserviceable parts. Do not use electrical test equipment on any circuit related to the SRS airbag system. For required servicing o ...

Dtc p1530 battery current sensor circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P1530 BATTERY CURRENT SENSOR CIRCUIT LOWDTC detecting condition:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION&qu ...