Subaru Crosstrek Service Manual: Dtc b2785 lin communication

DTC detecting condition:

When the keyless access CM detected the collation system LIN bus communication error three times in a row.

Trouble symptom:

The keyless access function may not be operable.

CAUTION:

For replacement procedure of keyless access CM, ID code box and steering lock CM, refer to “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

1.CHECK DTC.

1) Using the Subaru Select Monitor, clear the memory. Clear Memory Mode">

2) Read the DTC using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is DTC B2785 displayed?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2785 LIN COMMUNICATION">Go to Step 2.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

2.CHECK HARNESS (OPEN CIRCUIT).

1) Disconnect the keyless access CM connector.

2) Disconnect the steering lock CM connector.

3) Disconnect the ID code box connector. (With ID code box)

4) Using the tester, measure the resistance between terminals.

Connector & terminal

(B574) No. 17 — (B424) No. 5:

(B574) No. 17 — (B422) No. 2: (with ID code box)

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2785 LIN COMMUNICATION">Go to Step 3.

Repair or replace the open circuit of harness.

3.CHECK HARNESS (GROUND SHORT CIRCUIT).

Using the tester, measure the resistance between terminals.

Connector & terminal

(B424) No. 5 — Chassis ground:
(B574) No. 17 — Chassis ground:
(B422) No. 5 — Chassis ground: (with ID code box)

Is the resistance 10 k? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2785 LIN COMMUNICATION">Go to Step 4.

Repair or replace the short circuit of the harness.

4.CHECK HARNESS.

1) Connect the keyless access CM connector only.

2) Read the DTC using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is DTC B2785 displayed?

Replace the keyless access CM. Keyless Access CM">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2785 LIN COMMUNICATION">Go to Step 5.

5.CHECK ID CODE BOX.

NOTE:

For model without ID code box, go to the next step.

1) Connect the ID code box.

2) Read the DTC using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is DTC B2785 displayed?

Replace the ID code box. ID Code Box">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2785 LIN COMMUNICATION">Go to Step 6.

6.CHECK STEERING LOCK CM.

1) Connect the steering lock CM. Steering Lock CM">

2) Using the Subaru Select Monitor, clear the memory. Clear Memory Mode">

3) Read the DTC using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is DTC B2785 displayed?

Replace the steering lock CM. Steering Lock CM">

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Dtc b2784 antenna circuit (push engine switch)

Dtc b2786 steering lock cm communication

Other materials:

Removal
GLASS/WINDOWS/MIRRORS > Remote Control Mirror SwitchREMOVAL1. Disconnect the ground cable from battery and wait for at least 60 seconds before starting work. NOTE">2. Remove the trim panel - front door. Door Trim > REMOVAL">3. Remove the panel - power window main switch. Pow ...

Inspection
CLUTCH SYSTEM > Master CylinderINSPECTIONIf any damage, deformation, wear, swelling, rust or other faults are found on the cylinder, piston, push rod, nipple, return spring, bleeder screw, seat or hose, replace the faulty part.(A)Master cylinder body(B)Seat(C)Return spring(D)Piston(E)Piston stop ...

Preparation tool
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS — SUBARU SELECT MONITOR 4Used for setting of each function and troubleshooting for electrical system.NOTE:For detailed operation procedures of Subaru Select ...