Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc b2329 rear radar axis alignment incomplete

Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE

DTC DETECTING CONDITION:

Axis adjustment of the radar sensor has failed.

(Forced termination of the Subaru Select Monitor, improper location of the target reflector, or deviation of the radar sensor due to impact.)

TROUBLE SYMPTOM:

All functions of BSD/RCTA stop.

Fail icon is displayed in the combination meter LCD display.

Failure-related notification is displayed for approx. two seconds on LCD display in the combination meter.

NOTE:

Check and replace the side that displayed the DTC.

STEPCHECKYESNO

1.CHECK REAR BUMPER.

Check the rear bumper.

Is there any fault? (Stickered, trace of repainting, etc.)

Replace or repair the bumper. Rear Bumper">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 2.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 2.

2.CHECK RADAR SENSOR BRACKET.

1) Remove the rear bumper. Rear Bumper">

2) Check the mounting bracket of the radar sensor as well as its installation position. Radar Sensor">

Is there any fault? (Visible damage, deformation, etc.)

Replace the mounting bracket of the radar sensor, or repair the installation position. Radar Sensor">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 3.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 3.

3.ADJUSTMENT OF RADAR SENSOR AXIS.

1) Install the rear bumper.

2) Perform the adjustment of radar axis. Radar Sensor > ADJUSTMENT">

3) Perform the Inspection Mode. Inspection Mode">

Is DTC B2329 displayed? (Current malfunction)

Replace the radar sensor. Radar Sensor">

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Dtc b2327 rear radar internal failure (internal electric circuit)
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2327 REAR RADAR INTERNAL FAILURE (INTERNAL ELECTRIC CIRCUIT)DTC DETECTING C ...

Dtc b2350 rear radar communication error between master and slave
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2350 REAR RADAR COMMUNICATION ERROR BETWEEN MASTER AND SLAVEDTC DETECTING C ...

Other materials:

Information display (if equipped)
NOTE For models with color multi function display, refer to "Multi function display" Outside temperature indicator Driving information display Clock With the ignition switch in the "ACC" position, the clock appears on the display. With the ignition switch in the "ON" position, ...

Dtc p0712 transmission fluid temperature sensor "a" circuit low
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0712 TRANSMISSION FLUID TEMPERATURE SENSOR "A" CIRCUIT LOWDTC detecting condition:Immediately at fault recognitionTrouble symptom:• Excessive shift shock• Shift cha ...

Inspection
POWER ASSISTED SYSTEM (POWER STEERING) > Electric Power Steering GearboxINSPECTION1. UNIT INSPECTIONCheck components for wear, damage or other faults. Adjust or replace if necessary.2. LIMITMake a measurements as follows. If it exceeds the specified service limits, adjust or replace.NOTE:When fix ...

© 2016-2026 Copyright www.sucross.com