Subaru Crosstrek Service Manual: Dtc b2284 brake signal correlation

DTC detecting condition:

When the brake signal transmitted via the hard wire and the brake signal transmitted from body integrated unit via CAN communication line do not match.

Trouble symptom:

CAUTION:

For replacement procedure of keyless access CM, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

1.CHECK LAN SYSTEM.

Inspect LAN system. Basic Diagnostic Procedure > PROCEDURE">

Is LAN system normal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 2.

Perform the inspection according to the diagnosis for LAN system.

2.CHECK CURRENT DATA.

Check the current data display of «Keyless Access with Push Button Start» using Subaru Select Monitor. Read Current Data">

• «Stop light SW»

Is DTC displayed normally according to the brake pedal operation?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 3.

Check the stop light system.

3.CHECK CURRENT DATA.

Confirm the current data display of «Body Control» using Subaru Select Monitor. Read Current Data">

• «Stop light SW»

Is DTC displayed normally according to the brake pedal operation?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 4.

Check body integrated unit Basic Diagnostic Procedure > PROCEDURE"> and the stop light switch circuit.

4.CHECK FUSE.

Check the fuse. Relay and Fuse">

Is the fuse OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 5.

Replace the fuse. When the replaced fuse is blown immediately, check the power supply circuit for short-circuited.

5.CHECK HARNESS.

1) Disconnect the keyless access CM connector.

2) Using a tester, measure the voltage between keyless access CM connectors.

Connector & terminal

(B572) No. 2 (+) — Chassis ground (−):

Is the voltage 9.5 — 16 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 6.

Check the power supply circuit.

6.CHECK HARNESS.

Using a tester, measure the resistance between the keyless access CM connector and chassis ground.

Connector & terminal

(B572) No. 11 — Chassis ground:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 7.

Repair or replace the open circuit of harness.

7.CHECK HARNESS.

1) Disconnect the stop light switch connector.

2) Using a tester, measure the resistance between the keyless access CM connector and stop light switch connector.

Connector & terminal

(B572) No. 18 — (B65) No. 4:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 8.

Repair or replace the open circuit of harness.

8.CHECK HARNESS.

Using a tester, measure the resistance between the keyless access CM connector and chassis ground.

Connector & terminal

(B572) No. 18 — Chassis ground:

Is the resistance 10 k? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2284 BRAKE SIGNAL CORRELATION">Go to Step 9.

Repair or replace the short circuit of the harness.

9.CHECK HARNESS.

Using a tester, measure the voltage between the keyless access CM connector and chassis ground when the brake pedal is depressed.

Connector & terminal

(B572) No. 18 (+) — Chassis ground (−):

Does the voltage change as follows? Brake pedal not depressed: 1 V or less > Brake pedal depressed: 11 — 14 V

Replace the keyless access CM. Keyless Access CM > REMOVAL">

Check the power supply circuit of stop light switch.

Dtc b2283 vehicle speed sensor

Dtc b2285 steering lock position signal correlation

Other materials:

Specification
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > General DescriptionSPECIFICATIONFuel tankCapacity60 L (15.9 US gal, 13.2 Imp gal)LocationUnder rear seatFuel pumpTypeImpellerShutoff discharge pressure750 kPa (7.7 kg/cm2, 108.8 psi) or lessDischarge rate82 L (21.7 US gal, 18 Imp gal)/h or more[12.5 V at 343 ...

Connecting a smartphone
If you connect a smartphone to this system after starting a supported aha application on the smartphone, you can display and operate the aha application displayed on the smartphone on the system screen. 1. Run the aha application on your smartphone. 2. Connect the iPhone/iPod touch to th ...

Disassembly
POWER ASSISTED SYSTEM (POWER STEERING) > Electric Power Steering GearboxDISASSEMBLYCAUTION:• Nut for fixing the rack is on the driver’s side only. When removing the tie-rod on the passenger’s side, turn over the boot - steering gearbox on the driver’s side, and fix the rac ...