Subaru Crosstrek Service Manual: Dtc b2283 vehicle speed sensor

DTC detecting condition:

Either of the following malfunctions is detected. (Vehicle speed sensor failure is detected.)

• Vehicle speed signal failure detection 1: Excessive deceleration detection

• Vehicle speed signal failure detection 2: Engine speed interlock detection

For replacement procedure of keyless access CM, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

1.CHECK LAN SYSTEM.

Inspect LAN system. Basic Diagnostic Procedure > PROCEDURE">

Is LAN system normal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2283 VEHICLE SPEED SENSOR">Go to Step 2.

Perform the inspection according to the diagnosis for LAN system.

2.CHECK COMBINATION METER.

Check that the speedometer is displayed normally.

Is the meter display normal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2283 VEHICLE SPEED SENSOR">Go to Step 3.

Check the VDC. Basic Diagnostic Procedure > PROCEDURE">

3.CHECK CURRENT DATA.

Check the current data display of «Keyless Access with Push Button Start» using Subaru Select Monitor. Read Current Data">

• «Vehicle speed signal»

Is the display normal according to the parked state or driving state?

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2283 VEHICLE SPEED SENSOR">Go to Step 4.

4.CHECK HARNESS (OPEN CIRCUIT).

1) Disconnect the keyless access CM connector.

2) Disconnect the combination meter connector.

3) Using a tester, measure the resistance between the keyless access CM connector and VDC CM connector.

Connector & terminal

Without EyeSight

(B574) No. 27 — (B310) No. 2:

With EyeSight

(B574) No. 27 — (B310) No. 24:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2283 VEHICLE SPEED SENSOR">Go to Step 5.

Repair or replace the open circuit of harness.

5.CHECK HARNESS (OPEN CIRCUIT).

Using a tester, measure the resistance between the keyless access CM connector and chassis ground.

Connector & terminal

(B574) No. 27 — Chassis ground:

Is the resistance 30 k? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2283 VEHICLE SPEED SENSOR">Go to Step 6.

Repair or replace the short circuit of the harness.

6.CHECK KEYLESS ACCESS CM.

1) Connect each connector.

2) Using the Subaru Select Monitor, measure the waveform between the terminals of keyless access CM.

Connector & terminal

(B574) No. 27 — Chassis ground:

Is 3.54 Hz displayed when the vehicle is driven at approx. 5 km/h? Or does the value change from 3.54 Hz when the vehicle stops?

Replace the keyless access CM. Keyless Access CM">

Check the VDC. Basic Diagnostic Procedure > PROCEDURE">

Dtc b2282 vehicle speed signal correlation

Dtc b2284 brake signal correlation

Other materials:

Inspection
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostics with PhenomenonINSPECTION1. THE SYSTEM DOES NOT NOTIFY THE TELEMATICS SERVICE PROVIDER CENTER AUTOMATICALLY AFTER COLLISIONNOTE:Perform the diagnostics for "Phone conversation is not possible. (The microphone does not respond to a voice. No sound ...

Inspection
LIGHTING SYSTEM > Door SwitchINSPECTION1. Check the resistance between switch terminals.Preparation tool:Circuit testerTerminal No.Inspection conditionsStandardConnection diagram1 — 3When door is openedLess than 1 ?When door is closed1 M? or more2. Replace the switch assembly - door if the insp ...

Dtc c2424 transmitter 4 battery voltage low
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C2424 TRANSMITTER 4 BATTERY VOLTAGE LOWDTC DETECTING CONDITION:Detected when power supply voltage failure signal is received from each transmitter.TROUBLE SYMPTOM:Tire pressure warning light ...