Subaru Crosstrek Service Manual: Dtc b2271 ign relay control circuit

DTC detecting condition:

• When malfunction is detected in IG1 and IG2 drive circuits in the keyless access CM.

• When malfunction is detected in IG hold circuit in the keyless access CM.

For replacement procedure of keyless access CM, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

1.CHECK LAN SYSTEM.

Inspect LAN system. Basic Diagnostic Procedure > PROCEDURE">

Is LAN system normal?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 2.

Perform the inspection according to the diagnosis for LAN system.

2.CHECK FUSE.

Check the fuse. Relay and Fuse">

Is the fuse OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 3.

Replace the fuse. When the replaced fuse is blown immediately, check the power supply circuit for short-circuited.

3.CHECK HARNESS.

1) Disconnect the keyless access CM connector.

2) Using a tester, measure the voltage between the keyless access CM connector and chassis ground.

Connector & terminal

(B572) No. 2 (+) — Chassis ground (−):

Is the voltage 9.5 — 16 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 4.

Check the power supply circuit.

4.CHECK HARNESS.

Using a tester, measure the resistance between the keyless access CM connector and chassis ground.

Connector & terminal

(B572) No. 11 — Chassis ground:

Is the resistance less than 1 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 5.

Repair or replace the open circuit of harness.

5.CHECK HARNESS.

1) Disconnect the keyless access CM connector.

2) Using a tester, measure the resistance between the keyless access CM connector and chassis ground.

Connector & terminal

(B572) No. 9 — Chassis ground:

Is resistance 74.15 — 460.88 ?? (20°C)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 6.

Check IG relay 2. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 7.

6.CHECK HARNESS.

1) Disconnect the keyless access CM connector.

2) Using a tester, measure the resistance between the keyless access CM connector and chassis ground.

Connector & terminal

(B574) No. 6 — Chassis ground:

Is resistance 50.87 — 72.17 ?? (20°C)

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 8.

Check IG relay 1. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 7.

7.CHECK RELAY.

Perform unit inspection of IG relay 1 and IG relay 2. Relay and Fuse > INSPECTION">

Is the relay OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2271 IGN RELAY CONTROL CIRCUIT">Go to Step 8.

Replace the relay. IG Relay1 (Push Button Start) > REMOVAL"> IG Relay2 (Push Button Start) > REMOVAL">

8.CHECK KEYLESS ACCESS CM.

1) Connect the keyless access CM connector.

2) Using a tester, measure the voltage between the terminals of keyless access CM connector.

Connector & terminal

(B574) No. 6 (+) — Chassis ground (−):
(B572) No. 9 (+) — Chassis ground (−):

Is the voltage 1 V or less > 9.5 — 16 V when ACC > IGN ON?

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Replace the keyless access CM. Keyless Access CM > REMOVAL">

Dtc b1242 wireless tuner

Dtc b2274 acc relay control circuit

Other materials:

Fuel pressure Inspection
MECHANICAL(H4DO) > Fuel PressureINSPECTION1. Release the fuel pressure. Fuel > PROCEDURE">2. Open the fuel filler lid and remove the fuel filler cap.NOTE:This operation is required to release the inner pressure of the fuel tank.3. Disconnect the fuel delivery tube from the fuel delive ...

Dtc p0354 ignition coil "d" primary control circuit/open
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0354 IGNITION COIL "D" PRIMARY CONTROL CIRCUIT/OPENNOTE:For the diagnostic procedure, refer to DTC P0351. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0351 IGNITION COIL " ...

System operation
Operating conditions The BSD/RCTA will operate when all of the following conditions are met. The ignition switch is in the "ON" position. The BSD/RCTA warning indicator and BSD/RCTA OFF indicator are turned off. The vehicle is driven at speeds above 6 mph (10 km/h) (except when rever ...