Subaru Crosstrek Service Manual: Dtc b1833 short in curtain shield airbag rh squib circuit (to +b)

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Curtain airbag harness (RH) is shorted to power supply.

• Curtain airbag module (RH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, curtain airbag module RH and the curtain airbag sensor RH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1833 SHORT IN CURTAIN SHIELD AIRBAG RH SQUIB CIRCUIT (TO +B)">Go to Step 2.

2.CHECK CURTAIN AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB33), and connect the connector (1N) in test harness N to connector (AB33).

3) Connect the airbag resistor to the connector (2N) of test harness N.

4) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for six seconds and go off?

Replace the curtain airbag module (RH). Curtain Airbag Module">

Diagnostic Chart with Trouble Code > DTC B1833 SHORT IN CURTAIN SHIELD AIRBAG RH SQUIB CIRCUIT (TO +B)">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (CURTAIN AIRBAG MODULE HARNESS RH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB26) from seat belt pretensioner (RH).

3) Disconnect connector (AB24) from side airbag module (RH).

4) Disconnect the airbag resistor from test harness N.

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Connect the battery ground terminal and turn the ignition switch to ON.

8) Measure the voltage between connector (6AG) in the test harness AG and chassis ground.

Connector & terminal

(6AG) No. 6 (+) — Chassis ground (−):

(6AG) No. 8 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Diagnostic Chart with Trouble Code > DTC B1833 SHORT IN CURTAIN SHIELD AIRBAG RH SQUIB CIRCUIT (TO +B)">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1833 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1833 SHORT IN CURTAIN SHIELD AIRBAG RH SQUIB CIRCUIT (TO +B)">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1832 short in curtain airbag rh squib circuit (to ground)

Dtc b1835 short in curtain airbag lh squib circuit

Other materials:

Inspection
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Secondary Pressure SensorINSPECTION1. Start and warm up the engine.2. Depress the brake pedal, and shift the select lever to “D” range.3. Shift the select lever to “P” or “N” range.4. Depress the brake pedal and hold ...

Installation
SECURITY AND LOCKS > IG Relay1 (Push Button Start)INSTALLATIONCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">Install each part in the reverse order ...

Disassembly
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Reverse Check SleeveDISASSEMBLY1. Cover the reverse check sleeve with cloth, and remove the snap ring by using screwdriver.NOTE:If the snap ring is deformed or the spring repulsive force is not enough, replace with a new snap ring.(A)Snap ring2. Remove ...