Subaru Crosstrek Service Manual: Dtc b1828 short in side airbag lh (to +b)

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Side airbag harness (LH) is shorted to power supply.

• Side airbag module (LH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, side airbag module LH and the side airbag sensor LH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1828 SHORT IN SIDE AIRBAG LH (TO +B)">Go to Step 2.

2.CHECK SIDE AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB19), and connect the connector (1AJ) in test harness AJ to connector (AB19).

3) Connect the airbag resistor to the test harness AJ connector (3AJ).

4) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for six seconds and go off?

Replace the side airbag module (LH). Side Airbag Module > REMOVAL">

Diagnostic Chart with Trouble Code > DTC B1828 SHORT IN SIDE AIRBAG LH (TO +B)">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (SIDE AIRBAG MODULE HARNESS LH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB21) from seat belt pretensioner (LH).

3) Disconnect the connector (AB31) from curtain airbag module (LH).

4) Disconnect the airbag resistor from test harness.

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Connect the battery ground terminal and turn the ignition switch to ON.

8) Measure the voltage between connector (5AG) in the test harness AG and chassis ground.

Connector & terminal

(5AG) No. 1 (+) — Chassis ground (−):

(5AG) No. 3 (+) — Chassis ground (−):

Is the voltage less than 1 V?

Diagnostic Chart with Trouble Code > DTC B1828 SHORT IN SIDE AIRBAG LH (TO +B)">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1828 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1828 SHORT IN SIDE AIRBAG LH (TO +B)">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1827 short in side airbag lh (to ground)

Dtc b1830 short in curtain airbag rh squib circuit

Other materials:

Dtc u0156 lost communication with information center "a"
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0156 LOST COMMUNICATION WITH INFORMATION CENTER "A"DTC DETECTING CONDITION:No data is received from MFD.TROUBLE SYMPTOM:Display of MFD does not operate properly.STEPCHECKYESNO1.CHECK PERFORMING OF BAS ...

Fuses
CAUTION Never replace a fuse with one having a higher rating or with material other than a fuse because serious damage or a fire could result. The fuses are designed to melt during an overload to prevent damage to the wiring harness and electrical equipment. The fuses are located in two fuse ...

Dtc b1577 imm control module eeprom
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1577 IMM CONTROL MODULE EEPROM1. EXCEPT FOR C0 AND C5 MODELSDTC detecting condition:• Defective keyless access CM• When inaccessible to ROM in keyless access CM.STE ...