Subaru Crosstrek Service Manual: Dtc b1821 open in side airbag rh

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Side airbag harness (RH) circuit is open.

• Side airbag module (RH) is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module, side airbag module RH and the side airbag sensor RH.

Is there poor contact?

Replace the airbag rear harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1821 OPEN IN SIDE AIRBAG RH">Go to Step 2.

2.CHECK SIDE AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB24) from the side airbag module (RH), and connect the connector (1AJ) in the test harness AJ to connector (AB24).

3) Connect the airbag resistor to the test harness AJ connector (3AJ).

4) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for 6 seconds and go off?

Replace the side airbag module (RH). Side Airbag Module > REMOVAL">

Diagnostic Chart with Trouble Code > DTC B1821 OPEN IN SIDE AIRBAG RH">Go to Step 3.

3.CHECK AIRBAG REAR HARNESS (SIDE AIRBAG MODULE HARNESS RH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connector (AB26) from seat belt pretensioner (RH).

3) Disconnect the connector (AB33) from curtain airbag module (RH).

4) Disconnect the airbag resistor from test harness AJ.

5) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

6) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

7) Measure the resistance between connector in the test harness AG and connector in the test harness AJ.

Connector & terminal

(5AG) No. 5 — (3AJ) No. 1:
(5AG) No. 7 — (3AJ) No. 2:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B1821 OPEN IN SIDE AIRBAG RH">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1821 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1821 OPEN IN SIDE AIRBAG RH">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1820 short in side airbag rh

Dtc b1822 short in side airbag rh (to ground)

Other materials:

Installation
POWER ASSISTED SYSTEM (POWER STEERING) > Universal JointINSTALLATION1. Before installation, check the universal joint assembly - steering. Universal Joint > INSPECTION">2. Adjust the tilt position of the column assembly - steering to the neutral position and lock the tilt lever.3. Ali ...

Clear memory mode Operation
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Clear Memory ModeOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the vehicle information and select «Confirmed».3. On «Main Menu» display, select «Each System».4. On «Select System» displa ...

Dtc b2a0a red led circuit
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2A0A RED LED CIRCUITDiagnosis start condition:When ACC is ON.DTC detecting condition:• Current in LED is less than 1 mA. (Improper LED connection, etc.)• Current is more than 200 mA for at le ...