AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble Code
DTC B1817 SHORT IN PASSENGER’S AIRBAG DUAL STAGE - 2ND STEP (TO GROUND)
Diagnosis start condition:
Ignition voltage is 10 V to 16 V.
DTC detecting condition:
• Airbag main harness circuit is shorted to ground.
• Airbag module harness (passenger’s side) circuit is shorted to ground.
• Passenger’s airbag module is faulty.
• Airbag control module is faulty.
CAUTION:
Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">
Wiring diagram:
Airbag system Airbag System > WIRING DIAGRAM">
STEP | CHECK | YES | NO |
1.CHECK POOR CONTACT OF CONNECTORS.
Check for poor contact of the connectors between the airbag control module and the passenger’s airbag module.
Is there poor contact?
Replace the airbag harness.
Diagnostic Chart with Trouble Code > DTC B1817 SHORT IN PASSENGER’S AIRBAG DUAL STAGE - 2ND STEP (TO GROUND)">Go to Step 2.
2.CHECK AIRBAG MAIN HARNESS (PASSENGER’S AIRBAG HARNESS).
1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.
2) Disconnect the connectors (AB7) and (AB2).
3) Disconnect the connector (AB66) from the driver’s knee airbag module.
4) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.
5) Disconnect the passenger’s airbag module connector (AB9).
6) Using a probe, measure the resistance between the connector (AB9) and chassis ground. General Description > PREPARATION TOOL">
CAUTION:
When measuring the resistance, make sure that the probe is inserted from the back side (harness side) of the connector. Also, do not insert the probe forcibly.
Connector & terminal
(AB9) No. 3 — Chassis ground:
(AB9) No. 4 — Chassis ground:
Is the resistance 1 M? or more?
Diagnostic Chart with Trouble Code > DTC B1817 SHORT IN PASSENGER’S AIRBAG DUAL STAGE - 2ND STEP (TO GROUND)">Go to Step 3.
Replace the airbag main harness along with body harness.
3.CHECK AIRBAG CONTROL MODULE.
1) Connect the connectors (AB6, AB17, AB18) and the airbag control module.
2) Using a probe, short the terminals No. 3 and No. 4 of connector (AB9). General Description > PREPARATION TOOL">
CAUTION:
When shorting the terminals, make sure that the probe is inserted from the back side (harness side) of the connector. Also, do not insert the probe forcibly.
Connector & terminal
(AB9) No. 3 — (AB9) No. 4:
3) Connect the battery ground terminal and turn the ignition switch to ON.
4) Perform the Inspection Mode. Inspection Mode">
5) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">
Is DTC B1817 displayed?
Replace the airbag control module. Airbag Control Module > REMOVAL">
Diagnostic Chart with Trouble Code > DTC B1817 SHORT IN PASSENGER’S AIRBAG DUAL STAGE - 2ND STEP (TO GROUND)">Go to Step 4.
4.CHECK PASSENGER’S AIRBAG MODULE.
1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.
2) Release the short circuit of connector (AB9).
3) Connect the passenger’s airbag module connector (AB9).
4) Connect the connectors (AB7) and (AB2).
5) Connect the connector (AB66) to the driver’s knee airbag module.
6) Connect the battery ground terminal and turn the ignition switch to ON.
7) Perform the Inspection Mode. Inspection Mode">
8) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">
Is DTC B1817 displayed?
Replace the passenger’s airbag module. Passenger’s Airbag Module > REMOVAL">
Diagnostic Chart with Trouble Code > DTC B1817 SHORT IN PASSENGER’S AIRBAG DUAL STAGE - 2ND STEP (TO GROUND)">Go to Step 5.
5.CHECK FOR ANY OTHER DTC ON DISPLAY.
Is any other DTC displayed?
Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">
Finish the diagnosis.
Installation
MECHANICAL(H4DO) > Cam CarrierINSTALLATION1. CAM CARRIER RH1. Insert the steel rods into ST, and set the engine so that the camshaft RH is facing up.CAUTION:• If the engine is standing on one side without inserting the steel rod into ST, engine may lose balance and fall down. Be sure to ins ...
General precautions regarding SRS airbag system
WARNING
To obtain maximum protection in
the event of an accident, the
driver and all passengers must
always wear seatbelts when in
the vehicle. The SRS airbag is
designed only to be a supplement
to the primary protection
provided by the seatbelt. It does
not eliminate the need to ...
Removal
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Oil PumpREMOVAL1. Remove the transmission assembly from the vehicle. Automatic Transmission Assembly > REMOVAL">2. Remove the torque converter assembly. Torque Converter Assembly > REMOVAL">3. Remove the oil pump chain cover. Oi ...