Subaru Crosstrek Service Manual: Dtc b1806 open in passenger s airbag

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Airbag main harness circuit is open.

• Airbag module harness (passenger’s side) circuit is open.

• Passenger’s airbag module is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module and the passenger’s airbag module.

Is there poor contact?

Replace the airbag harness.

Diagnostic Chart with Trouble Code > DTC B1806 OPEN IN PASSENGER’S AIRBAG">Go to Step 2.

2.CHECK AIRBAG MAIN HARNESS (PASSENGER’S AIRBAG HARNESS).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connectors (AB7) and (AB2).

3) Disconnect the connector (AB66) from the driver’s knee airbag module.

4) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

5) Disconnect the passenger’s airbag module connector (AB9).

6) Using a probe, measure the resistance between the terminals of connector (AB9). General Description > PREPARATION TOOL">

CAUTION:

When measuring the resistance, make sure that the probe is inserted from the back side (harness side) of the connector. Also, do not insert the probe forcibly.

Connector & terminal

(AB9) No. 1 — (AB9) No. 2:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B1806 OPEN IN PASSENGER’S AIRBAG">Go to Step 3.

Replace the airbag main harness along with body harness.

3.CHECK AIRBAG CONTROL MODULE.

1) Connect the connectors (AB6, AB17, AB18) and the airbag control module.

2) Connect the connectors (AB7) and (AB2).

3) Connect the connector (AB66) to the driver’s knee airbag module.

4) Using a probe, short the terminals No. 1 and No. 2 of connector (AB9). General Description > PREPARATION TOOL">

CAUTION:

When shorting the terminals, make sure that the probe is inserted from the back side (harness side) of the connector. Also, do not insert the probe forcibly.

Connector & terminal

(AB9) No. 1 — (AB9) No. 2:

5) Connect the battery ground terminal and turn the ignition switch to ON.

6) Perform the Inspection Mode. Inspection Mode">

7) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1806 displayed?

Replace the airbag control module. Airbag Control Module > REMOVAL">

Diagnostic Chart with Trouble Code > DTC B1806 OPEN IN PASSENGER’S AIRBAG">Go to Step 4.

4.CHECK PASSENGER’S AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Connect the passenger’s airbag module connector (AB9).

3) Connect the battery negative terminal, and clear the memory. Clear Memory Mode">

4) Perform the Inspection Mode. Inspection Mode">

5) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1806 displayed?

Replace the passenger’s airbag module. Passenger’s Airbag Module > REMOVAL">

Diagnostic Chart with Trouble Code > DTC B1806 OPEN IN PASSENGER’S AIRBAG">Go to Step 5.

5.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1805 short in passenger s airbag

Dtc b1807 short in passenger s airbag (to ground)

Other materials:

Keyless access setting (models with "keyless access with pushbutton start system")
Preparation for keyless access settings 1. Perform the preparation steps according to "Preparation for car settings" 2. Operate the " " or "  " switch to select the "Keyless Access Setting" item. Then push the   button. Driver's door unlock setting 1. Perform the preparatio ...

Removal
EXHAUST(H4DO) > Front Exhaust PipeREMOVALCAUTION:Vehicle components are extremely hot after driving. Be wary of receiving burns from heated parts.1. Disconnect the ground cable from battery. NOTE">2. Lift up the vehicle.3. Remove the under cover. Front Under Cover > REMOVAL"> ...

Gross Axle Weight (GAW) and Gross Axle Weight Rating (GAWR)
Gross Axle Weight The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehicle. The front and rear GAWR of your vehicle that is given by SUBARU are also ...