Subaru Crosstrek Service Manual: Dtc b1801 open in driver s airbag

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Airbag main harness circuit is open.

• Airbag module harness (driver’s side) circuit is open.

• Roll connector is open.

• Driver’s airbag module is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

Prior to starting work, prepare two AIRBAG RESISTORs (98299PA040).

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module and the driver’s airbag module.

Is there poor contact?

Replace the airbag harness.

Diagnostic Chart with Trouble Code > DTC B1801 OPEN IN DRIVER’S AIRBAG">Go to Step 2.

2.CHECK DRIVER’S AIRBAG MODULE.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Remove the driver’s airbag module.

3) Connect the connector (1N) in the test harness N to the connector (AB38).

4) Connect the airbag resistor to the connector (2N) of test harness N.

5) Connect the connector (1Q) in the test harness Q to connector (AB37).

6) Connect the airbag resistor to the connector (2Q) in the test harness Q.

7) Connect the battery ground terminal and turn the ignition switch to ON.

Does the airbag warning light illuminate for six seconds and go off?

Replace the driver’s airbag module. Driver’s Airbag Module">

Diagnostic Chart with Trouble Code > DTC B1801 OPEN IN DRIVER’S AIRBAG">Go to Step 3.

3.CHECK ROLL CONNECTOR AND AIRBAG MAIN HARNESS (DRIVER’S AIRBAG HARNESS).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Remove the console front panel and disconnect the connector (AB9).

3) Disconnect the driver’s knee airbag module connector (AB66).

4) Disconnect the airbag resistor from the connector (2N) in test harness N.

5) Disconnect the airbag resistor from the connector (2Q) of test harness Q.

6) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

7) Measure the resistance between connector (2Q) terminals in test harness Q.

Connector & terminal

(2Q) No. 1 — (2Q) No. 2:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B1801 OPEN IN DRIVER’S AIRBAG">Go to Step 5.

Diagnostic Chart with Trouble Code > DTC B1801 OPEN IN DRIVER’S AIRBAG">Go to Step 4.

4.CHECK ROLL CONNECTOR.

1) Remove the instrument panel lower cover and column cover, and disconnect the connector (AB7) from (AB2).

2) Measure the resistance between connector (2Q) terminals in test harness Q.

Connector & terminal

(2Q) No. 1 — (2Q) No. 2:

Is the resistance less than 10 ??

Replace the airbag main harness along with body harness.

Replace the roll connector. Roll Connector">

5.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B1801 displayed?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1801 OPEN IN DRIVER’S AIRBAG">Go to Step 6.

6.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1800 short in driver s airbag

Dtc b1802 short in driver s airbag (to ground)

Other materials:

Birthday setting
1. Perform the preparation steps according to "Preparation for date setting" 3- 56. 2. Operate the " " or " " switch to select the "Birthday" item. Then push the button. 3. Select an entry in the list to set by operating the "  " or " " switch. Then push the ...

Assembly
REAR SUSPENSION > Front Lateral LinkASSEMBLY1. Before assembly, inspect the following items and replace any faulty part with a new one.• Visually check the lateral link assembly - front for damage and deformation.• Visually check the bushing for abnormal cracks, fatigue or damage.&bul ...

Power steering warning light
This warning light illuminates when the ignition switch is turned to the "ON" position and turns off after the engine has started. This indicates that the warning system is working properly. While the engine is running, this warning light illuminates when a malfunction has been detected ...