Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc b16f1 passenger s seat belt warning failure

AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble Code

DTC B16F1 PASSENGER’S SEAT BELT WARNING FAILURE

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

Airbag control module is faulty.

Meter is faulty.

Harness circuits between meter and airbag control module are open, shorted or shorted to ground.

CAUTION:

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

Wiring diagram:

Airbag system Airbag System > WIRING DIAGRAM">

STEPCHECKYESNO

1.CHECK AIRBAG HARNESS.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

3) Connect the battery ground terminal and turn the ignition switch to ON.

Does the passenger’s seat belt warning light blink for 6 seconds and go off?

Diagnostic Chart with Trouble Code > DTC B16F1 PASSENGER’S SEAT BELT WARNING FAILURE">Go to Step 3.

Diagnostic Chart with Trouble Code > DTC B16F1 PASSENGER’S SEAT BELT WARNING FAILURE">Go to Step 2.

2.CHECK AIRBAG HARNESS.

1) Turn the ignition switch to OFF.

2) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

3) Measure the resistance between connector (2AG) in the test harness AG and chassis ground.

Connector & terminal

(2AG) No. 10 — Chassis ground:

Is the resistance 1 M? or more?

Replace the meter. Combination Meter > REMOVAL">

Repair the bulkhead harness and instrument panel harness. Or replace the airbag main harness along with body harness.

3.CHECK AIRBAG HARNESS.

1) Turn the ignition switch to OFF.

2) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

3) Connect the connectors (7AG) and (8AG) in the test harness AG.

4) Turn the ignition switch to ON.

Does the passenger’s seat belt warning light blink for 6 seconds, then repeatedly light and go off?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B16F1 PASSENGER’S SEAT BELT WARNING FAILURE">Go to Step 4.

4.CHECK AIRBAG HARNESS.

1) Turn the ignition switch to OFF.

2) Disconnect the connectors (7AG) and (8AG) in the test harness AG in the condition of step 3.

3) Disconnect the connector (i10) from meter.

4) Measure the resistance between connector (2AG) in the test harness AG and connector (i10).

Connector & terminal

(2AG) No. 10 — (i10) No. 16:

Is the resistance less than 10 ??

Replace the meter. Combination Meter > REMOVAL">

Repair the bulkhead harness and instrument panel harness. Or replace the airbag main harness along with body harness.

Dtc b161a lost communication with front satellite sensor bus
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B161A LOST COMMUNICATION WITH FRONT SATELLITE SENSOR BUSDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting ...

Dtc b1800 short in driver s airbag
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1800 SHORT IN DRIVER’S AIRBAGDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Ai ...

Other materials:

Other markings
The following makings are also placed on the sidewall. Maximum permissible inflation pressure The maximum cold inflation pressure to which this tire may be inflated. For example, "300 kPa (44 PSI) MAX. PRESS" Maximum load rating The load rating at the maximum permissible weight load for th ...

Removal
SEAT BELT SYSTEM > Front Seat BeltREMOVAL1. SEAT BELT OUTER - FRONTCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">• Airbag system sat ...

Dtc p0458 evap system (cpc) purge control valve "a" circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0458 EVAP SYSTEM (CPC) PURGE CONTROL VALVE "A" CIRCUIT LOWDTC detecting condition:Detected when two consecutive driving cycles with fault occur.Trouble symptom:Improper idlingCAUTION:After servicing ...

© 2016-2025 Copyright www.sucross.com