Subaru Crosstrek Service Manual: Dtc b1660 passenger s airbag on indicator failure

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Passenger’s airbag indicator is faulty.

• Airbag control module is faulty.

• Airbag main harness circuit is open or shorted.

• Body harness circuit is open.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK FOR POOR CONTACT.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Check that the connector between the airbag control module and MFD is securely connected.

Is there poor contact of any connector?

Repair the bulkhead harness. Or replace the airbag main harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B1660 PASSENGER’S AIRBAG ON INDICATOR FAILURE">Go to Step 2.

2.CHECK AIRBAG MAIN HARNESS.

1) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

2) Connect the battery ground terminal and turn the ignition switch to ON.

NOTE:

Neither of ON/OFF illuminates when it is normal.

Does the passenger’s airbag indicator illuminate?

Diagnostic Chart with Trouble Code > DTC B1660 PASSENGER’S AIRBAG ON INDICATOR FAILURE">Go to Step 3.

Diagnostic Chart with Trouble Code > DTC B1660 PASSENGER’S AIRBAG ON INDICATOR FAILURE">Go to Step 4.

3.CHECK AIRBAG MAIN HARNESS.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Remove the MFD and disconnect the connector (i122).

3) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

4) Measure the resistance between connector (2AG) in the test harness AG and chassis ground.

Connector & terminal

(2AG) No. 9 — (2AG) No. 8:

(2AG) No. 9 — Chassis ground:

(2AG) No. 8 — Chassis ground:

Is the resistance 1 M? or more?

Replace the MFD. Multi-function Display (MFD) > REMOVAL">

Repair the bulkhead harness. Or replace the airbag main harness along with body harness.

4.CHECK AIRBAG MAIN HARNESS.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Disconnect the connectors (AB6, AB17, AB18) from the airbag control module, and connect the connector (1AH) in the test harness AH.

3) Connect the connector (2AH) in the test harness AH and the connector (1AG) in the test harness AG.

4) Connect the connectors (7AG) and (8AG) in the test harness AG.

5) Connect the battery ground terminal and turn the ignition switch to ON.

Does the passenger’s airbag indicator illuminate?

Replace the airbag control module. Airbag Control Module">

Diagnostic Chart with Trouble Code > DTC B1660 PASSENGER’S AIRBAG ON INDICATOR FAILURE">Go to Step 5.

5.CHECK AIRBAG MAIN HARNESS.

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Remove the MFD and disconnect the connector (i122).

3) Measure the resistance between connector (2AG) in the test harness AG and connector (i122).

Connector & terminal

(2AG) No. 9 — (i122) No. 11:

(2AG) No. 8 — (i122) No. 10:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B1660 PASSENGER’S AIRBAG ON INDICATOR FAILURE">Go to Step 6.

Repair the bulkhead harness. Or replace the airbag main harness along with body harness.

6.CHECK BODY HARNESS.

1) Turn the ignition switch to ON.

2) Measure the voltage between connector (i122) and chassis ground.

Connector & terminal

(i122) No. 3 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Replace the MFD. Multi-function Display (MFD) > REMOVAL">

Check the power supply circuit of MFD.

Dtc b1655 front buckle switch rh failure

Dtc b1675 satellite safing sensor failure

Other materials:

Open/close
To open: First unlock the rear gate lock then push the rear gate opener button. To close: Lower the rear gate slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip. WARNING To prevent dangerous exhaust ...

Removal
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Fuel Delivery and Evaporation LinesREMOVALWARNING:Place “NO OPEN FLAMES” signs near the working area.CAUTION:Be careful not to spill fuel.1. Release the fuel pressure. Fuel > PROCEDURE">2. Open the fuel filler lid and remove the fuel f ...

Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Blower Resistor (Manual A/C Model)INSPECTION1. Check the resistance between resistor terminals.Preparation tool:Circuit testerTerminal No.StandardConnection diagram4 — 3Approx. 0.43 ?4 — 2Approx. 1.03 ?4 — 1Approx. 3 ?2. Replace the resistor if the ...