Subaru Crosstrek Service Manual: Dtc b161a lost communication with front satellite sensor bus

Diagnosis start condition:

Ignition voltage is 10 V to 16 V.

DTC detecting condition:

• Harness between airbag control module and front sub sensor is open or shorted.

• Front sub sensor is faulty.

• Airbag control module is faulty.

Before performing diagnosis, refer to “CAUTION” in “General Description”. General Description > CAUTION">

1.CHECK POOR CONTACT OF CONNECTORS.

Check for poor contact of the connectors between the airbag control module and the front sub sensor.

Is there poor contact?

Replace the airbag main harness along with body harness.

Diagnostic Chart with Trouble Code > DTC B161A LOST COMMUNICATION WITH FRONT SATELLITE SENSOR BUS">Go to Step 2.

2.CHECK AIRBAG MAIN HARNESS (FRONT SENSOR BUS LH).

1) Turn the ignition switch to OFF, disconnect the battery ground cable, and wait for 60 seconds or more.

2) Remove the instrument panel lower cover and column cover, and disconnect the connectors (AB7) and (AB2).

3) Remove the console front panel and disconnect the connector (AB9).

4) Disconnect the connectors (AB6, AB17, AB18) from airbag control module.

5) Connect the connector (1AG) in the test harness AG to the connectors (AB6, AB17, AB18).

6) Disconnect the connector (AB13) from the front sub sensor (LH), and then connect the connector (1H) in the test harness H to connector (AB13).

7) Measure the resistance between connector (4AG) in the test harness AG and connector (3H) in the test harness H.

Connector & terminal

(4AG) No. 7 — (3H) No. 5:

(4AG) No. 9 — (3H) No. 6:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B161A LOST COMMUNICATION WITH FRONT SATELLITE SENSOR BUS">Go to Step 3.

Replace the airbag main harness along with body harness.

3.CHECK AIRBAG MAIN HARNESS (FRONT SENSOR BUS LH).

Measure the resistance between connector (4AG) in the test harness AG and chassis ground, and the resistance between connector (4AG) terminals in the test harness AG.

Connector & terminal

(4AG) No. 7 — Chassis ground:

(4AG) No. 9 — Chassis ground:

(4AG) No. 7 — (4AG) No. 9:

Is the resistance 1 M? or more?

Diagnostic Chart with Trouble Code > DTC B161A LOST COMMUNICATION WITH FRONT SATELLITE SENSOR BUS">Go to Step 4.

Replace the airbag rear harness along with body harness.

4.CHECK AIRBAG MAIN HARNESS (FRONT SENSOR BUS RH).

1) Disconnect the connector (AB16) from the front sub sensor (RH), and then connect the connector (1H) in the test harness H to connector (AB16).

2) Measure the resistance between connector (4AG) in the test harness AG and connector (3H) in the test harness H.

Connector & terminal

(4AG) No. 14 — (3H) No. 5:

(4AG) No. 12 — (3H) No. 6:

Is the resistance less than 10 ??

Diagnostic Chart with Trouble Code > DTC B161A LOST COMMUNICATION WITH FRONT SATELLITE SENSOR BUS">Go to Step 5.

Replace the airbag main harness along with body harness.

5.CHECK AIRBAG MAIN HARNESS (FRONT SENSOR BUS RH).

Measure the resistance between connector (4AG) in the test harness AG and chassis ground, and the resistance between connector (4AG) terminals in the test harness AG.

Connector & terminal

(4AG) No. 12 — Chassis ground:

(4AG) No. 14 — Chassis ground:

(4AG) No. 12 — (4AG) No. 14:

Is the resistance 1 M? or more?

Diagnostic Chart with Trouble Code > DTC B161A LOST COMMUNICATION WITH FRONT SATELLITE SENSOR BUS">Go to Step 6.

Replace the airbag rear harness along with body harness.

6.CHECK AIRBAG CONTROL MODULE.

1) Connect all connectors.

2) Clear the memory. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. (Current malfunction) Read Diagnostic Trouble Code (DTC)">

Is DTC B161A displayed?

Replace the front sub sensor (LH) and front sub sensor (RH). Front Sub Sensor > REMOVAL"> Replace the airbag control module if not operating normally even after replacing the sensor. Airbag Control Module > REMOVAL">

Diagnostic Chart with Trouble Code > DTC B161A LOST COMMUNICATION WITH FRONT SATELLITE SENSOR BUS">Go to Step 7.

7.CHECK FOR ANY OTHER DTC ON DISPLAY.

Is any other DTC displayed?

Check DTC using “List of Diagnostic Trouble Code”. List of Diagnostic Trouble Code (DTC)">

Finish the diagnosis.

Dtc b1698 door sensor lh initialization incomplete

Dtc b16f1 passenger s seat belt warning failure

Other materials:

Assembly
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reverse Brake AssemblyASSEMBLY1. Install the reverse brake piston.NOTE:Apply CVTF to the sealing area of reverse brake piston.2. Install the return spring.3. Install the spring retainer.4. Compress the return spring using the ST to install the snap ring ...

Inspection
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Warning Light Illumination PatternINSPECTION(1)Ignition switch(6)Light OFF(11)2 seconds or more(2)OFF(7)Light ON(12)Brake warning light (EBD warning light)(3)ON(8)2 seconds(13)Parking brake(4)Engine start(9)VDC OFF indicator light(14)Released(5)ABS w ...

Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Blower Resistor (Manual A/C Model)INSPECTION1. Check the resistance between resistor terminals.Preparation tool:Circuit testerTerminal No.StandardConnection diagram4 — 3Approx. 0.43 ?4 — 2Approx. 1.03 ?4 — 1Approx. 3 ?2. Replace the resistor if the ...