HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC B14E6 MODE DOOR ACTUATOR STEPPING MOTOR CIRCUIT SHORT-CIRCUIT
DTC detecting condition:
Mode door actuator stepping motor circuit is shorted.
Trouble symptom:
Vent does not change.
Wiring diagram:
Air conditioning system Air Conditioning System > WIRING DIAGRAM">
STEP | CHECK | YES | NO |
1.CHECK CONNECTOR.
1) Check the condition of connector connection.
2) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is B14E6 displayed?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B14E6 MODE DOOR ACTUATOR STEPPING MOTOR CIRCUIT SHORT-CIRCUIT">Go to Step 2.
Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE:
In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.
2.CHECK POWER SUPPLY FOR MODE DOOR ACTUATOR.
1) Turn the ignition switch to OFF.
2) Disconnect the mode door actuator connector.
3) Turn the ignition switch to ON.
4) Measure the voltage between the mode door actuator connector terminal and chassis ground.
Connector & terminal
(B77) No. 3 (+) — Chassis ground (–):
Is the voltage approx. 10 V or more?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B14E6 MODE DOOR ACTUATOR STEPPING MOTOR CIRCUIT SHORT-CIRCUIT">Go to Step 3.
Check the DC power supply circuit.
3.CHECK MODE DOOR ACTUATOR.
1) Turn the ignition switch to OFF.
2) Measure the resistance between mode door actuator terminals using a tester.
Connector & terminal
(B77) No. 3 — No. 1:
(B77) No. 3 — No. 2:
(B77) No. 3 — No. 5:
(B77) No. 3 — No. 6:
Is the resistance 80 — 100 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B14E6 MODE DOOR ACTUATOR STEPPING MOTOR CIRCUIT SHORT-CIRCUIT">Go to Step 4.
Replace the actuator. Mode Door Actuator > REMOVAL">
4.CHECK HARNESS BETWEEN A/C CONTROL PANEL AND MODE DOOR ACTUATOR (SHORTED TO POWER SUPPLY).
1) Disconnect the A/C control panel connector.
2) Turn the ignition switch to ON.
3) Measure the voltage between mode door actuator connector and chassis ground.
Connector & terminal
(B77) No. 1 (+) — Chassis ground (−):
(B77) No. 2 (+) — Chassis ground (−):
(B77) No. 5 (+) — Chassis ground (−):
(B77) No. 6 (+) — Chassis ground (−):
Is there any voltage?
Repair or replace the short circuit of the harness.
Replace the A/C control panel. Control Panel > REMOVAL">
Removal
AIRBAG SYSTEM > Side Airbag SensorREMOVALCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">• Airbag system satellite safing sensor is lo ...
Dtc b1815 short in passenger s airbag dual stage - 2nd step
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1815 SHORT IN PASSENGER’S AIRBAG DUAL STAGE - 2ND STEPDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Airbag main harness circuit is shorted.• Airbag module harness circuit ...
Treadwear
The treadwear grade is a comparative
rating based on the wear rate of
the tire when tested under controlled
conditions on a specified
government test course.
For example, a tire graded 150
would wear one and one-half (1-
1/2) times as well on the government
course as a tire graded 100.
...