Subaru Crosstrek Service Manual: Dtc b1409 scu communication

DTC detecting condition:

Communication failure between body integrated unit and security control module

CAUTION:

When the body integrated unit is replaced, registration of the immobilizer system is required. For details, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

1.CHECK GROUNDING POINT.

Check the ground point of chassis ground.

Are there any loose connections, any foreign objects caught in the ground lines or contact surface, or any fluid stains?

Remove the foreign matters, and tighten to the specified torque. Then start the engine, and check that the fault was removed. Check DTC Read Diagnostic Trouble Code (DTC)">, and when DTC B1572 is still displayed, Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 2.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 2.

2.CHECK BODY INTEGRATED UNIT POWER SUPPLY CIRCUIT.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from body integrated unit.

3) Measure the voltage between the body integrated unit connector terminal and chassis ground.

Connector & terminal

(i84) No. 6 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 3.

Check the harness for open or short circuit between body integrated unit and fuse.

3.CHECK BODY INTEGRATED UNIT POWER SUPPLY CIRCUIT.

1) Turn the ignition switch to ON.

2) Measure the voltage between the body integrated unit connector terminal and chassis ground.

Connector & terminal

(B281) No. 3 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 4.

Check the harness for open or short circuit between the body integrated unit and ignition switch.

4.CHECK BODY INTEGRATED UNIT GROUND CIRCUIT (OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Measure the resistance between the body integrated unit connector terminal and chassis ground.

Connector & terminal

(B280) No. 1 — Chassis ground:

(i84) No. 1 — Chassis ground:

Is the resistance less than 10 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 5.

Repair the open circuit of the body integrated unit ground circuit.

5.CHECK SECURITY CONTROL MODULE POWER SUPPLY CIRCUIT.

1) Disconnect the connector from the security control module.

2) Measure the voltage between security control module connector terminal and chassis ground.

Connector & terminal

(B559) No. 1 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 6.

Check for an open or short circuit in the harness between security control module and fuse.

6.CHECK SECURITY CONTROL MODULE GROUND CIRCUIT (OPEN).

Measure the resistance between security control module connector terminal and chassis ground.

Connector & terminal

(B559) No. 5 — Chassis ground:

Is the resistance less than 10 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 7.

Repair the open circuit of the security control module ground circuit.

7.CHECK HARNESS (OPEN CIRCUIT) BETWEEN BODY INTEGRATED UNIT AND SECURITY CONTROL MODULE.

Measure the resistance between the body integrated unit connector terminal and security control module connector terminal.

Connector & terminal

(B280) No. 21 — (B559) No. 3:

Is the resistance less than 10 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 8.

Repair the harness between body integrated unit and security control module.

8.CHECK COMMUNICATION LINE HARNESS (SHORT CIRCUIT TO POWER SUPPLY).

1) Turn the ignition switch to ON.

2) Measure the voltage between security control module connector terminal and chassis ground.

Connector & terminal

(B559) No. 3 (+) — Chassis ground (−):

Is the voltage 6 V or more?

Repair the harness between body integrated unit and security control module.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 9.

9.CHECK COMMUNICATION CIRCUIT HARNESS (SHORT CIRCUIT TO GROUND).

1) Turn the ignition switch to OFF.

2) Measure the resistance between security control module connector terminal and chassis ground.

Connector & terminal

(B559) No. 3 — Chassis ground:

Is the resistance less than 10 ??

Repair the harness between body integrated unit and ECM.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1409 SCU COMMUNICATION">Go to Step 10.

10.CHECK SECURITY CONTROL MODULE.

1) Replace the security control module. (Do not perform security control module registration.)

2) Turn the ignition switch to ON.

3) Perform the Clear Memory Mode. Clear Memory Mode">

4) Read the DTC of the body integrated unit. Read Diagnostic Trouble Code (DTC)">

Is DTC B1409 detected?

Replace the body integrated unit. Body Integrated Unit">

Security control module was defective. Perform security control module registration. Refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

Dtc b1408 meter non-volatile memory

Dtc b1410 transponder communication

Other materials:

Component
REAR SUSPENSION > General DescriptionCOMPONENT1. REAR SUSPENSION(1)Rear sub frame ASSY(11)Stopper LWRTightening torque: N·m (kgf-m, ft-lb)(2)Stopper UPR(12)Flange nutT1:30 (3.06, 22.1)(3)Stay - rear frame COMPL(13)Rear stabilizerT2:33 (3.36, 24.3)(4)Front sub frame support(14)Bushing - sta ...

Dtc b2a05 left speaker/audio circuit
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2A05 LEFT SPEAKER/AUDIO CIRCUITDiagnosis start condition:When ACC is ON.DTC detecting condition:Speaker impedance is more than 10 k? for 100 ms. (Detached speaker connection, etc.)Trouble symptom:• ...

Dtc p1496 coil 3 egr "a" control circuit low
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P1496 COIL 3 EGR "A" CONTROL CIRCUIT LOWNOTE:For the diagnostic procedure, refer to DTC P1498. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P1498 COIL 4 EGR "A" CONTROL ...