Subaru Crosstrek Service Manual: Dtc b1015 key interlock circuit

DTC detecting condition:

Ground short of key interlock circuit

Trouble symptom:

Key interlock does not keep lock condition.

Wiring diagram:

Shift lock control system Shift Lock Control System > WIRING DIAGRAM">

1.CHECK DTC.

1) Insert the ignition key.

2) Turn the ignition switch to ON.

3) Shift to the Neutral range.

4) Shift into P range.

5) Shift to the Neutral range.

6) Shift into P range.

7) Shift to the Neutral range.

8) Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is B1015 current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 2.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 8.

2.CHECK DTC.

1) Shift the select lever to P range.

2) Remove the ignition key.

3) Disconnect the key actuator connector (B557) and body integrated unit connector (B281).

4) Connect the disconnected connectors.

5) Insert the ignition key.

6) Turn the ignition switch to ON and shift into Neutral.

7) Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is B1015 current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 3.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 8.

3.CHECK KEY ACTUATOR.

1) Turn the ignition switch to OFF.

2) Disconnect the key actuator connector (B557).

3) Measure the resistance between key actuator connectors.

Terminals

No. 1 — No. 2:

Is the resistance 103 — 115 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 4.

Replace the key actuator. Key Lock Cylinders">

4.CHECK KEY ACTUATOR.

Connect the battery terminals to the key actuator.

Terminals

No. 2 — Positive terminal:
No. 1 — Ground terminal:

Is the actuator activated and then key locked?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 5.

Replace the key actuator. Key Lock Cylinders">

5.CHECK HARNESS.

1) Disconnect the body integrated unit connector (B281).

2) Measure the resistance between body integrated unit and key actuator using tester.

Connector & terminal

(B557) No. 1 — (B281) No. 4:

Is the resistance less than 10 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 6.

Repair or replace the open circuit of harness.

6.CHECK HARNESS.

Measure the resistance between body integrated unit and chassis ground using tester.

Connector & terminal

(B281) No. 4 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 7.

Repair or replace the short circuit of the harness.

7.CHECK HARNESS.

1) Connect the body integrated unit.

2) Turn the ignition switch to ON.

3) Measure the voltage between body integrated unit and chassis ground using tester.

Connector & terminal

(B281) No. 4 (+) — Chassis ground (−):

Is the voltage 6 V or more?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1015 KEY INTERLOCK CIRCUIT">Go to Step 8.

Replace the body integrated unit. Body Integrated Unit">

8.CHECK CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the body integrated unit connector (B281) and key actuator connector (B557).

Is there poor contact at disconnected connector terminal?

Repair the terminal where poor contact exists, or replace harness.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Dtc b1014 acc power

General description

Other materials:

Air bleeding Procedure
BRAKE > Air BleedingPROCEDURECAUTION:• Do not let brake fluid come into contact with the painted surface of the vehicle body. Wash away with water immediately and wipe off if it is spilled by accident.• Avoid mixing brake fluid of different brands or different grades even from the sam ...

Dtc c1212 front right abs sensor signal
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C1212 FRONT RIGHT ABS SENSOR SIGNALNOTE:For the diagnostic procedure, refer to “DTC C1242 REAR LEFT ABS SENSOR SIGNAL”. Diagnostic Procedure with Diagnostic Trouble Code (DTC) &g ...

Note
GLASS/WINDOWS/MIRRORS > Power Window SystemNOTEFor operation procedures of each component of the power window system, refer to the respective sections.• Power window control switch: Power Window Control Switch">• Front door glass: Front Door Glass">• Front regu ...