Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc b1014 acc power

BODY CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC B1014 ACC POWER

DTC detecting condition:

Voltage failure caused by poor contact of ACC power supply circuit

Trouble symptom:

DRL may not illuminate.

Wiring diagram:

Shift lock control system Shift Lock Control System > WIRING DIAGRAM">

STEPCHECKYESNO

1.CHECK DTC.

Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is B1014 current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1014 ACC POWER">Go to Step 2.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1014 ACC POWER">Go to Step 5.

2.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect and then connect the body integrated unit connector.

3) Wait approx. 2 minutes.

4) Turn the ignition switch to ON.

5) Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is B1014 current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1014 ACC POWER">Go to Step 3.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1014 ACC POWER">Go to Step 5.

3.CHECK FUSE.

1) Turn the ignition switch to OFF.

2) Check the fuse.

Is the fuse OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1014 ACC POWER">Go to Step 4.

Replace the defective fuse.

4.CHECK HARNESS.

1) Disconnect the body integrated unit connector.

2) Using the tester, measure the voltage between terminals.

Connector & terminal

(B280) No. 32 (+) — Chassis ground (−):

Is the voltage 8.5 — 16.5 V?

Replace the body integrated unit. Body Integrated Unit">

Repair the harness between body integrated unit and fuse.

5.CHECK CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the body integrated unit connector.

Is there poor contact of connector?

Repair or replace the poor contact of connector.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Dtc b1013 ignition power
BODY CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1013 IGNITION POWERDTC detecting condition:Voltage failure caused by poor contact of IGN power supply ...

Dtc b1015 key interlock circuit
BODY CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1015 KEY INTERLOCK CIRCUITDTC detecting condition:Ground short of key interlock circuitTrouble sympto ...

Other materials:

Removal
BRAKE > Rear Disc RotorREMOVAL1. Lift up the vehicle, and then remove the rear wheels.2. Release the lever assembly - hand brake.3. Remove the caliper body assembly from the housing assembly - rear axle.(1) Remove the bolt from the brake hose bracket.(2) Remove the mounting bolt, and remove the c ...

Dtc b2a0c dcm internal fault
TELEMATICS SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2A0C DCM INTERNAL FAULTDIAGNOSIS START CONDITION:When ignition switch is ON.DTC DETECTING CONDITION:• Main microcomputer and communication circuit IC cannot communicate. (Defective IPC)• SIM ...

Inspection
COMMUNICATION SYSTEM > HornINSPECTION1. CHECK HORN ASSEMBLY1. Remove the horn assembly (Hi & Lo). Horn > REMOVAL">2. Check the horn sounds when applying the battery voltage to the horn assembly.Terminal No.Inspection conditionsSpecificationHorn terminal (+) — Horn case (−) ...

© 2016-2022 Copyright www.sucross.com