Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc b1013 ignition power

BODY CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC B1013 IGNITION POWER

DTC detecting condition:

Voltage failure caused by poor contact of IGN power supply circuits

Trouble symptom:

Symptoms such as shift lock or wiper not operating may occur.

Wiring diagram:

Shift lock control system Shift Lock Control System > WIRING DIAGRAM">

STEPCHECKYESNO

1.CHECK DTC.

Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is B1013 current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1013 IGNITION POWER">Go to Step 2.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1013 IGNITION POWER">Go to Step 5.

2.CHECK DTC.

1) Turn the ignition switch to OFF.

2) Disconnect and then connect the body integrated unit connector.

3) Wait approx. 2 minutes.

4) Turn the ignition switch to ON.

5) Read the DTC of body integrated unit using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">

Is B1013 current malfunction?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1013 IGNITION POWER">Go to Step 3.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1013 IGNITION POWER">Go to Step 5.

3.CHECK FUSE.

1) Turn the ignition switch to OFF.

2) Check the fuse.

Is the fuse OK?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B1013 IGNITION POWER">Go to Step 4.

Replace the defective fuse.

4.CHECK HARNESS.

1) Disconnect the body integrated unit connector.

2) Using the tester, measure the voltage between terminals.

Connector & terminal

(B281) No. 3 (+) — Chassis ground (−):

Is the voltage 8.5 — 16.5 V?

Replace the body integrated unit. Body Integrated Unit">

Repair the harness between body integrated unit and fuse.

5.CHECK CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the body integrated unit connector.

Is there poor contact of connector?

Repair or replace the poor contact of connector.

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Dtc b1012 battery backup power supply
BODY CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1012 BATTERY BACKUP POWER SUPPLYDTC detecting condition:Voltage failure caused by poor contact of bat ...

Dtc b1014 acc power
BODY CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B1014 ACC POWERDTC detecting condition:Voltage failure caused by poor contact of ACC power supply circ ...

Other materials:

Refrigerant leak check Inspection
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > Refrigerant Leak CheckINSPECTION1. Attach the manifold gauge set.Preparation tool:Manifold gauge set(1) Check that all valves are fully closed.(2) Install the low/high pressure hoses to the service ports on the low/high pressure sides of the vehicle resp ...

Removal
EMISSION CONTROL (AUX. EMISSION CONTROL DEVICES)(H4DO) > Purge Control Solenoid ValveREMOVAL1. Disconnect the ground cable from battery.2. Remove the bolt which holds the purge control solenoid valve onto intake manifold.NOTE:Hold the purge control solenoid valve unit by hand to prevent it from r ...

Installation
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reduction Driven GearINSTALLATION1. Install the reduction driven gear assembly and spacer oil.Tightening torque:17 N·m (1.7 kgf-m, 12.5 ft-lb)2. Select the transfer drive gear shim. Reduction Drive Gear > ADJUSTMENT">3. Install the pa ...

© 2016-2022 Copyright www.sucross.com