Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Diagnostics chart for security indicator light Inspection

Subaru Crosstrek Service Manual / Immobilizer (diagnostics) / Diagnostics chart for security indicator light Inspection

IMMOBILIZER (DIAGNOSTICS) > Diagnostics Chart for Security Indicator Light

INSPECTION

1. CHECK SECURITY INDICATOR LIGHT CIRCUIT

CAUTION:

When the body integrated unit is replaced, registration of the immobilizer system is required. For details, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

Wiring diagram:

Immobilizer system Immobilizer System > WIRING DIAGRAM">

STEPCHECKYESNO

1.CHECK FUSE.

1) Remove the ignition key from ignition switch. Or, turn off the power.

2) Check the fuse (M/B No. 8).

Is the fuse OK?

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 2.

Replace the fuse. If the replaced fuse blows out easily, repair the short circuit in the harness between the fuse and body integrated unit.

2.CHECK SECURITY INDICATOR LIGHT.

1) Disconnect the connector from body integrated unit.

2) Connect the resistor (100 ?) between the body integrated unit connector terminal (i171) No. 26 and chassis ground.

Does the security indicator light illuminate?

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 3.

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 5.

3.CHECK BODY INTEGRATED UNIT GROUND CIRCUIT (OPEN CIRCUIT).

Measure the resistance between the body integrated unit connector terminal and chassis ground.

Connector & terminal

(B280) No. 1 — Chassis ground:

(i84) No. 1 — Chassis ground:

Is the resistance less than 10 ??

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 4.

Repair the open circuit of the body integrated unit ground circuit.

4.CHECK BODY INTEGRATED UNIT POWER SUPPLY CIRCUIT.

Measure the voltage between the body integrated unit connector terminal and chassis ground.

Connector & terminal

(B281) No. 7 (+) — Chassis ground (−):

(i84) No. 6 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Replace the body integrated unit. Body Integrated Unit">

Check the harness for open or short circuit between body integrated unit and fuse.

5.CHECK COMBINATION METER CIRCUIT.

1) Remove the combination meter. Combination Meter">

2) Measure the voltage between combination meter connector terminal and chassis ground.

Connector & terminal

(i10) No. 40 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 6.

Check for an open or short circuit in the harness between the combination meter and fuse.

6.CHECK COMBINATION METER CIRCUIT (OPEN).

Measure the resistance between the body integrated unit connector terminal and combination meter connector terminal.

Connector & terminal

(i171) No. 26 — (i10) No. 1:

Is the resistance less than 10 ??

LED bulb is defective. Replace the combination meter case assembly. Combination Meter > DISASSEMBLY">

Repair the harness or connector.

2. CHECK KEY SWITCH CIRCUIT

CAUTION:

When the body integrated unit is replaced, registration of the immobilizer system is required. For details, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.

Wiring diagram:

Immobilizer system Immobilizer System > WIRING DIAGRAM">

STEPCHECKYESNO

1.CHECK POWER SUPPLY CIRCUIT.

1) Disconnect the connector from key warning switch.

2) Measure the voltage between key warning switch connector terminal and chassis ground.

Connector & terminal

(B555) No. 1 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 2.

Check the harness for an open or short between the key warning switch and fuse.

2.CHECK KEY WARNING SWITCH.

1) Insert the ignition key in the ignition switch. (OFF or ACC)

2) Measure the resistance between key warning switch connector terminals.

Terminals

No. 1 — No. 2:

Is the resistance less than 1 ??

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 3.

Replace the key warning switch. Key Lock Cylinders">

3.CHECK KEY WARNING SWITCH.

1) Remove the ignition key from ignition switch.

2) Measure the resistance between key warning switch connector terminals.

Terminals

No. 1 — No. 2:

Is the resistance 1 M? or more?

Diagnostics Chart for Security Indicator Light > INSPECTION">Go to Step 4.

Replace the key warning switch. Key Lock Cylinders">

4.CHECK HARNESS BETWEEN KEY WARNING SWITCH AND BODY INTEGRATED UNIT (OPEN).

1) Disconnect the connector from body integrated unit.

2) Measure the resistance between key warning switch connector terminal and body integrated unit connector terminal.

Connector & terminal

(B555) No. 2 — (B280) No. 4:

Is the resistance less than 10 ??

Replace the body integrated unit. Body Integrated Unit">

Repair the harness between key warning switch and body integrated unit.

Clear memory mode Operation
IMMOBILIZER (DIAGNOSTICS) > Clear Memory ModeOPERATIONNOTE:For detailed operation procedures, refer to “Application help”.1. ECM1. On «Start» display, select «Diagnosis».2. On «Veh ...

Electrical component location Location
IMMOBILIZER (DIAGNOSTICS) > Electrical Component LocationLOCATION(1)Security indicator light (LED bulb)(3)Data link connector(5)Transponder(2)Body integrated unit(4)Antenna(6)Security control modul ...

Other materials:

Removal
SECURITY AND LOCKS > Immobilizer AntennaREMOVAL1. MODEL WITHOUT KEYLESS ACCESS WITH PUSH BUTTON START1. Disconnect the ground cable from battery. NOTE">2. Remove the cover assembly - column.(1) Remove the screws by turning the steering wheel to right and left.(2) Release the claw, and re ...

Locking and unlocking from the inside
Unlock Lock To lock the door from the inside, rotate the lock lever forward. To unlock the door from the inside, rotate the lock lever rearward. The red mark on the lock lever appears when the door is unlocked. Pull the inside door handle to open an unlocked door. Always mak ...

Inspection
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Rear Oxygen SensorINSPECTION1. Check that the rear oxygen sensor has no deformation, cracks or other damages.2. Measure the resistance between rear oxygen sensor terminals.Terminal No.Standard1 and 25.6+1.7 −0.6 ? (when 20°C (68°F) ...

© 2016-2024 Copyright www.sucross.com