Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Diagnostic procedure without diagnostic trouble code (dtc) Check shift indicator

Subaru Crosstrek Service Manual / Continuously variable transmission (diagnostics) / Diagnostic procedure without diagnostic trouble code (dtc) Check shift indicator

CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure without Diagnostic Trouble Code (DTC)

CHECK SHIFT INDICATOR

Diagnosis:

CAN communication is abnormal with the combination meter.

Combination meter malfunction

Trouble symptom:

Shift indicator does not display or remains displayed.

Shift indicator display does not change.

STEPCHECKYESNO

1.CHECK DTC.

Read the DTC relating the TCM using the Subaru Select Monitor.

Is DTC U0155 or U0423 displayed?

Perform the self-diagnosis of combination meter.

Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 2.

2.CHECK DTC.

Read the DTC relating the TCM using the Subaru Select Monitor.

Are DTCs other than U0155 and U0423 displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 3.

3.CHECK COMBINATION METER.

Read DTC of combination meter.

Are any DTCs displayed?

Perform the diagnosis according to DTC.

Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 4.

4.CHECK TCM.

1) Operate the + side of the paddle shift switch.

2) Read the data of «Up Switch» using the Subaru Select Monitor.

Does it change between ON and OFF according to the operation?

Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 5.

Check for poor contact between TCM and paddle shift UP switch, and repair the defective part.

5.CHECK TCM.

1) Operate the − side of the paddle shift switch.

2) Read the data of «Down Switch» using the Subaru Select Monitor.

Does it change between ON and OFF according to the operation?

Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 6.

Check for poor contact between TCM and paddle shift down switch, and repair the defective part.

6.CHECK TCM.

1) Turn the ignition switch OFF, then turn it ON again.

2) Shift the select lever to manual mode.

3) Read the data of «Shift step in Manu. mode» using the Subaru Select Monitor.

Is “1” displayed?

Diagnostic Procedure without Diagnostic Trouble Code (DTC) > CHECK SHIFT INDICATOR">Go to Step 7.

Perform the diagnosis according to DTC P0951. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0951 AUTO SHIFT MANUAL CONTROL CIRCUIT RANGE/PERFORMANCE">

7.CHECK TCM.

1) Shift up the select lever.

2) Read the data of «Shift step in Manu. mode» using the Subaru Select Monitor.

Is “2” displayed?

Current condition is normal.

Replace the TCM. Transmission Control Module (TCM)">

Diagnostic procedure for subaru select monitor communication Communication for initializing impossible
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure for Subaru Select Monitor CommunicationCOMMUNICATION FOR INITIALIZING IMPOSSIBLEDiagnosis:Defective harness connectorTrouble ...

Diagnostics with phenomenon Inspection
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostics with PhenomenonINSPECTIONSymptomsFaulty partsEngine stalls when driving in “D” or “R” range, or selecting &ldq ...

Other materials:

Electrical specification
HVAC SYSTEM (AUTO A/C) (DIAGNOSTICS) > Auto A/C Control Module I/O SignalELECTRICAL SPECIFICATIONTerminal No.ContentMeasuring conditionStandard1Mode door actuator #4Digital signal; can not be measured — 2Mode door actuator #3Digital signal; can not be measured — 3Mode door actuator #2Digital ...

Installing a rearward facing child restraint
1. Place the child restraint system in the rear seating position. 2. Run the lap and shoulder belt through or around the child restraint system following the instructions provided by its manufacturer. 3. Insert the tongue plate into the buckle until you hear a click. 4. Take up t ...

Compression Inspection
MECHANICAL(H4DO) > CompressionINSPECTIONCAUTION:After warming-up, engine becomes very hot. Be careful not to burn yourself during measurement.1. Turn the ignition switch to OFF.2. After warming-up the engine, turn the ignition switch to OFF.3. Make sure that the battery is fully charged.4. Check ...

© 2016-2022 Copyright www.sucross.com