Subaru Crosstrek Service Manual: Diagnostic procedure with cancel code Dtc b2328 rear radar internal failure (radar misalignment)
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Cancel Code
DTC B2328 REAR RADAR INTERNAL FAILURE (RADAR MISALIGNMENT)
DETECTING CONDITION:
• Excessive impact was given to the installation area of the radar sensor, which resulted in deviation of the radar sensor axis.
• Mounting bracket for the radar sensor is deformed.
• Defective radar sensor
TROUBLE SYMPTOMS:
• All functions of BSD/RCTA are temporarily suspended.
• The icon indicating function suspended will be displayed in the combination meter LCD display.
• Function-suspended confirmation will be displayed for approx. two seconds on LCD display in the combination meter.
NOTE:
If DTC B2328 is detected repeatedly, check or replace the part corresponding to the cancel code.
| STEP | CHECK | YES | NO |
1.CHECK REAR BUMPER.
Check the rear bumper.
Is there any fault? (Stickered, trace of repainting, etc.)
Replace or repair the bumper. Rear Bumper">
Diagnostic Procedure with Cancel Code > DTC B2328 REAR RADAR INTERNAL FAILURE (RADAR MISALIGNMENT)">Go to Step 2.
Diagnostic Procedure with Cancel Code > DTC B2328 REAR RADAR INTERNAL FAILURE (RADAR MISALIGNMENT)">Go to Step 2.
2.CHECK RADAR SENSOR BRACKET.
1) Remove the rear bumper. Rear Bumper">
2) Check the mounting bracket of the radar sensor as well as its installation position. Radar Sensor">
Is there any fault? (Visible damage, deformation, etc.)
Replace the mounting bracket of the radar sensor, or repair the installation position. Radar Sensor">
Diagnostic Procedure with Cancel Code > DTC B2328 REAR RADAR INTERNAL FAILURE (RADAR MISALIGNMENT)">Go to Step 3.
Diagnostic Procedure with Cancel Code > DTC B2328 REAR RADAR INTERNAL FAILURE (RADAR MISALIGNMENT)">Go to Step 3.
3.ADJUSTMENT OF RADAR SENSOR AXIS.
1) Install the rear bumper.
2) Perform the adjustment of radar axis. Radar Sensor > ADJUSTMENT">
3) Read the cancel code. Read Cancel Code">
Is B2328 displayed?
Replace the radar sensor. Radar Sensor">
The circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE:
In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.
Clear memory mode Operation
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Clear Memory ModeOPERATION1. On «Start» display, select «Diagnosis».2. On «Vehicle selection» display, input the target vehicle i ...
Diagnostics with phenomenon Inspection
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostics with PhenomenonINSPECTIONSymptomsMaintenance partsBSD/RCTA does not operate.FuseLAN system Basic Diagnostic Procedure" ...
Other materials:
Language setting
1. Perform the preparation steps according
to "Preparation for screen settings"
2. Operate the "
" or "
" switch to
select the "Languages" item. Then push
the
button.
3. The current language setting will be
displayed. Push the
button to enter
the language s ...
Installation
HVAC SYSTEM (HEATER, VENTILATOR AND A/C) > FRESH/RECIRC Door ActuatorINSTALLATIONCAUTION:• After installing the grille assembly - ventilation RH, check that the air vent grille of the grille assembly - ventilation RH is inserted correctly into the air vent duct.• Before handling the a ...
Inspection
PARKING BRAKE > Parking Brake Assembly (Rear Disc Brake)INSPECTION1. Measure the inner diameter of the rear disc rotor. If scoring or worn is found on the disc, replace the rear disc rotor.Disc rotor inner diameter:Specification: 170 mm (6.69 in)Service limit: 171 mm (6.73 in)2. Measure the linin ...
