Subaru Crosstrek Service Manual: Diagnostic procedure for subaru select monitor communication Communication for initializing impossible

Diagnosis:

Defective harness connector

Trouble symptom:

Subaru Select Monitor communication failure

CAUTION:

Use the check board when measuring the TCM terminal voltage and resistance.

1.CHECK IGNITION SWITCH.

Is the ignition switch ON?

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 2.

Turn the ignition switch to ON, and select the transmission using the Subaru Select Monitor.

2.CHECK BATTERY.

1) Turn the ignition switch to OFF.

2) Measure the battery voltage.

Is the voltage 11 V or more?

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 3.

Charge or replace the battery.

3.CHECK BATTERY TERMINAL.

Is there poor contact at battery terminal?

Replace or tighten the battery terminal.

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 4.

4.CHECK INSTALLATION OF TCM CONNECTOR.

Turn the ignition switch to OFF.

Is the TCM connector inserted into the TCM until the clamp locks?

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 5.

Insert the TCM connector to TCM.

5.CHECK LAN SYSTEM.

Perform the diagnosis for LAN system. Basic Diagnostic Procedure">

Is there any fault in LAN system?

Perform the diagnosis according to DTC for LAN system. List of Diagnostic Trouble Code (DTC)">

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 6.

6.CHECK SUBARU SELECT MONITOR COMMUNICATION.

1) Turn the ignition switch to ON.

2) Check whether communication to transmission system can be executed normally.

Is «Select Function» displayed?

Check DTC of TCM. Read Diagnostic Trouble Code (DTC)">

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 7.

7.CHECK POWER SUPPLY CIRCUIT.

1) Turn the ignition switch to OFF.

2) Disconnect the TCM connector.

3) Turn the ignition switch to ON. (Engine OFF)

4) Measure the ignition power supply voltage between TCM connector and chassis ground.

Connector & terminal

(B54) No. 8 (+) — Chassis ground (−):

(B54) No. 24 (+) — Chassis ground (−):

(B54) No. 34 (+) — Chassis ground (−):

(B54) No. 40 (+) — Chassis ground (−):

(B54) No. 41 (+) — Chassis ground (−):

Is the voltage 10 — 13 V?

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 8.

Repair the open circuit of harness between TCM and battery.

8.CHECK HARNESS CONNECTOR BETWEEN TCM AND CHASSIS GROUND.

1) Turn the ignition switch to OFF.

2) Measure the resistance of harness between TCM connector and chassis ground.

Connector & terminal

(B54) No. 42 — Chassis ground:

Is the resistance less than 10 ??

Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">Go to Step 9.

Repair the open circuit of the TCM ground circuit and poor contact of connector.

9.CHECK POOR CONTACT OF CONNECTOR.

Is there poor contact of control module power supply, ground circuit and data link connector?

Repair the connector.

Replace the TCM. Transmission Control Module (TCM)">

Clear memory mode Operation

Diagnostic procedure without diagnostic trouble code (dtc) Check shift indicator

Other materials:

Warranties and maintenance
SUBARU warranties do not apply to vehicle damage or malfunction caused by trailer towing. If you use your vehicle to tow a trailer, more frequent maintenance will be required due to the additional load. (Refer to "Maintenance schedule under severe driving conditions" in the "Warranty and Ma ...

Dtc b2329 rear radar axis alignment incomplete
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETEDTC DETECTING CONDITION:Axis adjustment of the radar sensor has failed.(Forced termination of the Subaru Select Monitor, improper loca ...

Disassembly
DIFFERENTIALS > Rear Differential (T-type)DISASSEMBLYTo detect the real cause of trouble, inspect the following items before disassembling.• Tooth contact and backlash between hypoid driven gear and drive pinion• Hypoid driven gear runout on its back surface• Total preload of dr ...