AIRBAG SYSTEM > General Description
COMPONENT
(1) | Front sub sensor RH | (4) | Airbag warning light (in combination meter) | (7) | Airbag control module |
(2) | Front sub sensor LH | (5) | Airbag ON/OFF indicator light (MFD) | (8) | Knee airbag module |
(3) | Driver’s airbag module | (6) | Passenger’s airbag module | (9) | Steering roll connector |
(1) | Curtain airbag sensor LH | (7) | Side airbag module RH | (13) | Occupant detection sensor |
(2) | Curtain airbag module LH | (8) | Occupant detection control module | (14) | Curtain airbag sensor RH |
(3) | Seat belt pretensioner LH | (9) | Front door impact sensor RH | (15) | Curtain airbag module RH |
(4) | Front door impact sensor LH | (10) | Lap seat belt pretensioner RH | (16) | Satellite safing sensor |
(5) | Side airbag module LH | (11) | Side airbag sensor RH | (17) | Side airbag sensor LH |
(6) | Buckle switch RH | (12) | Seat belt pretensioner RH |
1. DRIVER’S AIRBAG MODULE
2. KNEE AIRBAG MODULE
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
3. PASSENGER’S AIRBAG MODULE
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
4. SIDE AIRBAG MODULE
Tightening torque:
6 N·m (0.61 kgf-m, 4.4 ft-lb)
5. CURTAIN AIRBAG MODULE
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
6. AIRBAG CONTROL MODULE
CAUTION:
Do not reuse mounting bolts and nuts.
Tightening torque:
25 N·m (2.55 kgf-m, 18.4 ft-lb)
7. FRONT SUB SENSOR
CAUTION:
Do not reuse mounting bolts and nuts.
Tightening torque:
13 N·m (1.33 kgf-m, 9.6 ft-lb)
8. FRONT DOOR IMPACT SENSOR
CAUTION:
Do not reuse mounting bolts and nuts.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
9. SIDE AIRBAG SENSOR
CAUTION:
Do not reuse mounting bolts and nuts.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
10. CURTAIN AIRBAG SENSOR
CAUTION:
Do not reuse mounting bolts and nuts.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
11. SATELLITE SAFING SENSOR
CAUTION:
Do not reuse mounting bolts and nuts.
Tightening torque:
7.5 N·m (0.76 kgf-m, 5.5 ft-lb)
12. STEERING ROLL CONNECTOR
Installation
GLASS/WINDOWS/MIRRORS > Front Door GlassINSTALLATIONCAUTION:• Check that the running channel - front door is securely fixed to the panel assembly - front door and to the sash COMPL - partition.• Before installing the glass assembly - front door, check the lip of the running channel - ...
Inspection
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Crankshaft Position SensorINSPECTION1. CRANKSHAFT POSITION SENSOR (METHOD WITH OSCILLOSCOPE)1. Prepare an oscilloscope.2. Remove the glove box. Glove Box > REMOVAL">3. Connect the probe to ECM connector.Terminal No.Probe16+1−4. Start the eng ...
Preparation tool
DRIVE SHAFT SYSTEM > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONPART NO.DESCRIPTIONREMARKS20099PA010INSTALLER & REMOVER• Used for replacing the rear bushing of rear axle housing.• Used together with BUSHING REMOVER (20099FG000).20099FG000BUSHING REMOVER• U ...