Subaru Crosstrek Service Manual: Component
VEHICLE DYNAMICS CONTROL (VDC) > General Description
COMPONENT
1. ABS WHEEL SPEED SENSOR
(1) | Front ABS wheel speed sensor | (4) | Rear ABS wheel speed sensor | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Housing ASSY - front axle | (5) | Magnetic encoder | T1: | 7.5 (0.8, 5.5) |
(3) | Housing ASSY - rear axle | (6) | Hub unit COMPL | T2: | 33 (3.4, 24.3) |
2. STEERING ANGLE SENSOR
(1) | Steering roll connector | (2) | Steering angle sensor |
3. VDC CONTROL MODULE & HYDRAULIC CONTROL UNIT (VDCCM&H/U)
• Models without EyeSight
(1) | Primary inlet | (7) | Rear LH outlet | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Secondary inlet | (8) | Damper - hydraulic unit | T1: | 7.5 (0.8, 5.5) |
(3) | VDC control module and hydraulic control unit (VDCCM&H/U) | (9) | Spacer | T2: | 15 (1.5, 11.1) |
(4) | Rear RH outlet | (10) | Nut | T3: | 19 (1.9, 14.0) |
(5) | Front LH outlet | (11) | Bracket - hydraulic unit | T4: | 33 (3.4, 24.3) |
(6) | Front RH outlet | T5: | VDC Control Module and Hydraulic Control Unit (VDCCM&H/U) > REPLACEMENT"> | ||
• Models with EyeSight
(1) | Hose ASSY | (8) | Front RH outlet | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Bracket - hydraulic unit | (9) | Primary inlet | T1: | 7.5 (0.8, 5.5) |
(3) | Damper - hydraulic unit | (10) | Rear LH outlet | T2: | 15 (1.5, 11.1) |
(4) | Spacer | (11) | Pipe A | T3: | 18 (1.8, 13.3) |
(5) | VDC control module and hydraulic control unit (VDCCM&H/U) | (12) | Pipe B | T4: | 19 (1.9, 14.0) |
(6) | Secondary inlet | (13) | Rear RH outlet | T5: | 33 (3.4, 24.3) |
(7) | Front LH outlet | ||||
Specification
VEHICLE DYNAMICS CONTROL (VDC) > General DescriptionSPECIFICATIONItemSpecification or identificationABS wheel speed sensorABS wheel speed sensor gap (for reference)Front0.77 — 1.43 mm (0.030 — ...
Preparation tool
VEHICLE DYNAMICS CONTROL (VDC) > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS — SUBARU SELECT MONITOR 4Used for setting of each function and trouble ...
Other materials:
Inspection
CLUTCH SYSTEM > Clutch SwitchINSPECTION1. CLUTCH START SWITCH1. Perform the following inspections. If the clutch start switch does not operate normally, adjust the switch, and check it again. Clutch Switch > ADJUSTMENT">• Make sure that engine does not start with clutch pedal no ...
Towing with all wheels on the ground
1. Release the parking brake and put the
transmission in the "N" position.
2. The ignition switch should be in the
"ON" position while the vehicle is being
towed.
3. Take up slack in the towline slowly to
prevent damage to the vehicle.
WARNING
Never turn the ignition switch to
t ...
Replacement
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Transmission Gear OilREPLACEMENT1. Pull out the oil level gauge.2. Lift up the vehicle.3. Using the TORX® bit T70, remove the drain plug, and drain the gear oil completely.CAUTION:• Immediately after the vehicle has been running or after idling f ...
