Subaru Crosstrek Service Manual: Component
STARTING/CHARGING SYSTEMS(H4DO) > General Description
COMPONENT
1. STARTER
(1) | Starter housing ASSY | (9) | Overrunning clutch | (17) | Sleeve bearing |
(2) | Sleeve bearing | (10) | Internal gear ASSY | (18) | Starter cover ASSY |
(3) | Shift lever | (11) | Shaft | ||
(4) | Plate | (12) | Pinion gear | Tightening torque: N·m (kgf-m, ft-lb) | |
(5) | Seal rubber | (13) | Seal rubber | T1: | 1.4 (0.1, 1.0) |
(6) | Magnet switch ASSY | (14) | Yoke ASSY | T2: | 6 (0.6, 4.4) |
(7) | Snap ring | (15) | Armature ASSY | T3: | 7.5 (0.8, 5.5) |
(8) | Stopper | (16) | Brush holder ASSY | T4: | 10 (1.0, 7.4) |
2. GENERATOR
(1) | Cap | (8) | Bearing | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Pulley | (9) | Stator coil | T1: | 2 (0.2, 1.5) |
(3) | Front cover | (10) | IC regulator | T2: | 3.9 (0.4, 2.9) |
(4) | Ball bearing | (11) | Brush | T3: | 4.4 (0.4, 3.2) |
(5) | Bearing retainer | (12) | Rectifier | T4: | 8.9 (0.9, 6.6) |
(6) | Spacer | (13) | Rear cover | T5: | 108 (11.0, 79.8) |
(7) | Rotor | (14) | Terminal B | ||
3. GENERATOR BRACKET
(1) | Generator | (7) | Idler pulley cover | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | V-belt cover bracket | (8) | V-belt | T1: | 6.4 (0.7, 4.7) |
(3) | Generator bracket | T2: | 15.5 (1.6, 11.4) | ||
(4) | V-belt tensioner ASSY | T3: | 25 (2.5, 18.4) | ||
(5) | Cap | T4: | 36 (3.7, 26.6) | ||
(6) | Idler pulley | T5: | Generator > INSTALLATION"> | ||
4. BATTERY CURRENT & TEMPERATURE SENSOR
(1) | Terminal boot | (7) | Starter | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Terminal fuse ASSY | (8) | Battery temperature sensor | T1: | 6 (0.6, 4.4) |
(3) | Battery cable ASSY | T2: | 7.5 (0.8, 5.5) | ||
(4) | Battery | T3: | 11 (1.1, 8.1) | ||
(5) | Battery cable bracket | T4: | 13 (1.3, 9.6) | ||
(6) | Battery cable stay | T5: | 14 (1.4, 10.3) | ||
Specification
STARTING/CHARGING SYSTEMS(H4DO) > General DescriptionSPECIFICATIONItemSpecificationsVehicle modelCVTMTStarterTypeReduction typeModelM000T38571M000T33176ManufacturerMitsubishi ElectricVoltage and ou ...
Preparation tool
STARTING/CHARGING SYSTEMS(H4DO) > General DescriptionPREPARATION TOOL1. GENERAL TOOLTOOL NAMEREMARKSCircuit testerUsed for measuring resistance, voltage and current.NOTE:• For measuring stand ...
Other materials:
List of diagnostic trouble code (dtc) List
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > List of Diagnostic Trouble Code (DTC)LISTDTCItemContent of diagnosisReferenceP0500VEHICLE SPEED SENSOR "A" CIRCUITWheel speed data from VDC CM&H/U is abnormal. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC P0500 V ...
Inspection
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Secondary Speed SensorINSPECTION1. Set the ST between the TCM and bulkhead harness.ST 18460AA040CHECK BOARD2. Set the probe of oscilloscope to the check board connector.Connector & terminalNo. 13 (+) — No. 42 (−):(A)+ probe(B)− prob ...
Outside temperature indicator
U.S.-spec. models
Except U.S.-spec. models
The outside temperature indicator shows
the outside temperature in a range from
−40 to 1228F (−40 to 508C).
The indicator can give a false reading
under any of the following conditions.
When there is too much sun.
During ...
