EXTERIOR BODY PANELS > General Description
COMPONENT
1. FRONT HOOD
(1) | Hood COMPL - front | (6) | Stopper - front hood | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Hinge COMPL - front hood | (7) | Stay - hood support | T1: | 25 (2.55, 18.4) |
(3) | Cover - front fender | (8) | Seal - front duct | T2: | 33 (3.36, 24.3) |
(4) | Insulator - front hood | (9) | Striker - front hood | ||
(5) | Buffer - front hood |
2. FRONT FENDER
(1) | Garnish ASSY - front fender | (3) | Cover - A pillar ASSY | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Fender COMPL - front | T: | 7.5 (0.76, 5.5) |
3. FRONT DOOR
(1) | Panel ASSY - front door | (6) | Upper hinge - front door | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Weather strip - front door | (7) | Weather strip outer - front door | T1: | 7.5 (0.76, 5.5) |
(3) | Sealing cover - front door | T2: | 25 (2.55, 18.4) | ||
(4) | Checker ASSY - front door | T3: | 30 (3.06, 22.1) | ||
(5) | Lower hinge - front door | T4: | 33 (3.36, 24.3) |
4. REAR DOOR
(1) | Panel ASSY - rear door | (7) | Upper hinge - rear door | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Weather strip - rear door | (8) | Weather strip outer - rear door | T1: | 7.5 (0.76, 5.5) |
(3) | Sealing cover - rear door | T2: | 25 (2.55, 18.4) | ||
(4) | Checker ASSY - rear door | T3: | 30 (3.06, 22.1) | ||
(5) | Catcher - rear door | T4: | 33 (3.36, 24.3) | ||
(6) | Lower hinge - rear door | T5: | 38 (3.87, 28.0) |
5. REAR GATE
(1) | Hinge - rear gate | (7) | Buffer - rear gate | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Plug - hole | (8) | Stopper - rear gate | T1: | 7.5 (0.76, 5.5) |
(3) | Panel - rear gate | (9) | Buffer - body side | T2: | 13 (1.33, 9.6) |
(4) | Latch & actuator - rear gate | (10) | Stay ASSY - rear gate | T3: | 20 (2.04, 14.8) |
(5) | Striker - rear gate | (11) | Drip - rear gate | T4: | 25 (2.55, 18.4) |
(6) | Handle - rear gate | (12) | Clip |
Electrical specification
POWER ASSISTED SYSTEM (POWER STEERING) (DIAGNOSTICS) > Control Module I/O SignalELECTRICAL SPECIFICATIONNOTE:The terminal numbers of the power steering control module connectors are as indicated in the figure.ContentsTerminal No.Input/output signalMeasured value and measuring conditionsPower supp ...
Inspection
MECHANICAL(H4DO) > Cylinder BlockINSPECTION1. CYLINDER BLOCK & PISTON1. Visually inspect to make sure that there are no cracks, scratches or other damage.2. Use liquid penetrant tester on the important sections to check for fissures.3. Check that there are no traces of gas leaking or water le ...
Disassembly
SUNROOF/T-TOP/CONVERTIBLE TOP (SUNROOF) > Sunroof AssemblyDISASSEMBLY1. Remove the screw and remove the sunroof motor.2. Remove the stopper rubber and pull out the sunshade assembly from the rail assembly - sunroof.3. Disconnect the claws and then remove the drain holder.4. Remove the screw and p ...