Subaru Crosstrek Service Manual: Component
EXHAUST(H4DO) > General Description
COMPONENT
1. FRONT EXHAUST PIPE AND CENTER EXHAUST PIPE
(1) | Front exhaust pipe | (12) | Front exhaust pipe lower cover | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Front catalytic converter | (13) | Front catalytic converter lower cover LH | T1: | 13 (1.3, 9.6) |
(3) | Center exhaust pipe | (14) | Front catalytic converter lower cover RH | T2: | 18 (1.8, 13.3) |
(4) | Rear catalytic converter | (15) | Front exhaust pipe side cover RH (front) | T3: | 23 (2.3, 17.0) |
(5) | Front oxygen (A/F) sensor | (16) | Front exhaust pipe side cover LH (front) | T4: | 30 (3.1, 22.1) |
(6) | Rear oxygen sensor | (17) | Front exhaust pipe side cover LH (rear) | T5: | 35 (3.6, 25.8) |
(7) | Gasket | (18) | Front exhaust pipe side cover RH (rear) | T6: | 42.5 (4.3, 31.3) |
(8) | Gasket | (19) | Center exhaust pipe upper cover | T7: | Front Oxygen (A/F) Sensor > INSTALLATION"> |
(9) | Front exhaust pipe upper cover | (20) | Band | T8: | Rear Oxygen Sensor > INSTALLATION"> |
(10) | Front catalytic converter upper cover LH | (21) | Hanger bracket (CVT model) | ||
(11) | Front catalytic converter upper cover RH | (22) | Hanger bracket (MT model) | ||
2. REAR EXHAUST PIPE AND MUFFLER
(1) | Gasket | (5) | Cushion rubber | Tightening torque: N·m (kgf-m, ft-lb) | |
(2) | Spring | (6) | Self-locking nut | T: | 48 (4.9, 35.4) |
(3) | Chamber | (7) | Gasket | ||
(4) | Rear exhaust pipe | (8) | Muffler | ||
3. HEAT SHIELD COVER
(1) | Center exhaust cover | (2) | Rear exhaust cover | Tightening torque: N·m (kgf-m, ft-lb) | |
T1: | 10 (1.0, 7.4) | ||||
T2: | 18 (1.8, 13.3) | ||||
Caution
EXHAUST(H4DO) > General DescriptionCAUTION• Prior to starting work, pay special attention to the following:1. Always wear work clothes, a work cap, and protective shoes. Additionally, wear a ...
Muffler
...
Other materials:
Welcome lighting function (if
equipped)
The welcome lighting function turns on the
low beam headlight for smooth approaching
to or exiting from the vehicle at night or
in a dark place.
The function is activated while all of the
following conditions are met.
The light control switch is in the
"AUTO" position
It is dark enoug ...
Hill start assist warning light does not come on
VEHICLE DYNAMICS CONTROL (VDC) (DIAGNOSTICS) > Warning Light Illumination PatternHILL START ASSIST WARNING LIGHT DOES NOT COME ONDetecting condition:Defective combination meterTrouble symptom:When the ignition switch is turned to ON (engine OFF), hill start assist warning light does not illuminat ...
Removal
MECHANICAL(H4DO) > Cylinder BlockREMOVAL1. Remove the engine from the vehicle. Engine Assembly > REMOVAL">2. Remove the intake manifold. Intake Manifold > REMOVAL">3. Remove the engine wiring harness. Engine Wiring Harness > REMOVAL">4. Remove the tumble genera ...
