Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Component

DIFFERENTIALS > General Description

COMPONENT

1. REAR DIFFERENTIAL (T-TYPE)

(1)

Hypoid driven gear and drive pinion set

(14)

O-ring

(27)

Filler plug

(2)

Pinion height adjusting washer

(15)

Side retainer shim

(28)

Drain plug

(3)

Rear bearing

(16)

Side retainer

(29)

Rear cover

(4)

Preload adjusting spacer

(17)

Side oil seal

(30)

Differential case

(5)

Preload adjusting washer

(18)

Side gear thrust washer

(31)

Gasket

(6)

Differential carrier

(19)

Side gear

(7)

Front bearing

(20)

Pinion mate gear

Tightening torque: N·m (kgf-m, ft-lb)

(8)

Spacer

(21)

Pinion mate gear washer

T1:

10.5 (1.1, 7.7)

(9)

Pilot bearing

(22)

Pinion shaft lock pin

T2:

29.5 (3.0, 21.8)

(10)

Front oil seal

(23)

Circlip

T3:

49 (5.0, 36.1)

(11)

Companion flange

(24)

Pinion mate shaft

T4:

103 (10.5, 76.0)

(12)

Self-locking nut

(25)

Air breather cap

T5:

181.5 (18.5, 133.9)

(13)

Side bearing

(26)

Stud bolt

2. REAR DIFFERENTIAL (VA1-TYPE)

(1)

Hypoid driven gear and drive pinion set

(13)

Lock plate

(25)

Stud bolt

(2)

Pinion height adjusting washer

(14)

Side bearing

(26)

Gasket

(3)

Rear bearing

(15)

O-ring

(27)

Filler plug

(4)

Preload adjusting spacer

(16)

Side retainer

(28)

Drain plug

(5)

Preload adjusting washer

(17)

Side oil seal

(29)

Rear cover

(6)

Differential carrier

(18)

Side gear thrust washer

(30)

Gasket

(7)

Front bearing

(19)

Side gear

(8)

Spacer

(20)

Pinion mate gear

Tightening torque: N·m (kgf-m, ft-lb)

(9)

Pilot bearing

(21)

Spring pin

T1:

25 (2.5, 18.4)

(10)

Front oil seal

(22)

Differential case

T2:

50 (5.1, 36.9)

(11)

Companion flange

(23)

Pinion mate shaft

T3:

Rear Differential (VA-type) > ASSEMBLY">

(12)

Self-locking nut

(24)

Air breather cap

T4:

191 (19.5, 140.9)

3. REAR DIFFERENTIAL MOUNTING SYSTEM

(1)

Rear differential front member

(4)

Rear sub frame

Tightening torque: N·m (kgf-m, ft-lb)

(2)

Rear differential member plate

(5)

Rear differential mount bushing

T1:

50 (5.1, 36.9)

(3)

Rear differential ASSY

(6)

Self-locking nut

T2:

70 (7.1, 51.6)

T3:

110 (11.2, 81.1)

Specification
DIFFERENTIALS > General DescriptionSPECIFICATION1. REAR DIFFERENTIALWhen replacing a rear differential assembly, select the correct one according to the following table.NOTE:• Using a differe ...

Preparation tool
DIFFERENTIALS > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS398477701HANDLE• Used for installing the rear bearing race.• Used for installi ...

Other materials:

Installation
BRAKE > Stop Light SwitchINSTALLATION1. BULB TYPE1. Install the stop light switch.CAUTION:• Turn the stop light switch clockwise when installing so that it can return backward by approximately 1 mm (0.04 in) and clearance is automatically adjusted.• If it is hard to turn the switch, r ...

Removal
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Mass Air Flow and Intake Air Temperature SensorREMOVAL1. Disconnect the ground cable from battery.2. Disconnect the connector (A) from the mass air flow and intake air temperature sensor, and remove the mass air flow and intake air temperature sensor. ...

Dtc u0101 lost communication with tcm
KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0101 LOST COMMUNICATION WITH TCMDetected when CAN data from TCM does not arrive.NOTE:Perform the diagnosis for LAN system. Basic Diagnostic Procedure > PROCEDURE"> ...

© 2016-2025 Copyright www.sucross.com