Subaru Crosstrek Service Manual: Basic diagnostic procedure Procedure

CAUTION:

Remove foreign matter (dust, water, oil etc.) from the VDCCM&H/U connector during removal and installation.

• To check the harness for open or short circuits, shake problem spot or connector.

• Refer to “Check List for Interview”. Check List for Interview">

1.CHECK PRE-INSPECTION.

1) Ask the customer when and how the trouble occurred using the interview check list. Check List for Interview">

2) Before performing diagnostics, check the component which might affect VDC problems. General Description > INSPECTION">

Is the check result OK?

Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.

Repair or replace each component.

2.CHECK INDICATION OF DTC.

1) Turn the ignition switch to OFF.

2) Connect the Subaru Select Monitor to data link connector.

3) Turn the ignition switch to ON and run the Subaru Select Monitor.

4) Read the DTC using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC) > OPERATION">

NOTE:

If the communication function of the Subaru Select Monitor cannot be executed properly, check the communication circuit. Subaru Select Monitor > INSPECTION">

Is DTC displayed on Subaru Select Monitor?

Record the DTC, time stamp and freeze frame data. Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.

NOTE:

• For the time stamp, refer to LAN section. General Description > CAUTION">

• Depending on DTCs, time stamp may not be stored.

Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.

3.PERFORM GENERAL DIAGNOSTICS.

1) Perform the inspection by referring to “General Diagnostic Table”. General Diagnostic Table > INSPECTION">

2) Perform the Clear Memory Mode. Clear Memory Mode > OPERATION">

3) Perform the Inspection Mode. Inspection Mode > PROCEDURE">

4) Read the DTC. Read Diagnostic Trouble Code (DTC) > OPERATION">

5) Check that the DTC is not displayed.

Do the VDC warning light & VDC indicator light, VDC OFF indicator light and ABS warning light go off after starting the engine?

Finish the diagnosis.

Check the combination meter circuit. Warning Light Illumination Pattern > ABS WARNING LIGHT DOES NOT GO OFF"> Warning Light Illumination Pattern > VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT GO OFF"> Warning Light Illumination Pattern > VDC OFF INDICATOR LIGHT DOES NOT GO OFF">

4.PERFORM DIAGNOSIS.

1) Refer to “List of Diagnostic Trouble Code (DTC)”.

NOTE:

For the DTC list, refer to “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC) > LIST">

2) Correct the cause of trouble.

3) Perform the Clear Memory Mode. Clear Memory Mode > OPERATION">

4) Perform the Inspection Mode. Inspection Mode > PROCEDURE">

5) Read the DTC. Read Diagnostic Trouble Code (DTC) > OPERATION">

Is DTC displayed?

Repeat step 4 until DTC is not shown.

Finish the diagnosis.

Hill start assist warning light does not come on

Check list for interview Check

Other materials:

Installation
GLASS/WINDOWS/MIRRORS > Windshield GlassINSTALLATIONCAUTION:• For model with EyeSight, always use Subaru genuine windshield glass specially designed for EyeSight. (If the windshield glass other than the glass specially designed for EyeSight is used, the visibility of the camera is blocked o ...

Removal
VEHICLE DYNAMICS CONTROL (VDC) > VDC OFF SwitchREMOVAL1. Disconnect the ground cable from battery. NOTE">2. Remove the cover assembly - instrument panel LWR driver OUT. Instrument Panel Lower Cover > REMOVAL">3. Remove the screws and release the claws, then detach the cover.4 ...

Inspection
CLUTCH SYSTEM > Clutch PedalINSPECTIONMove the clutch pedal pads in the lateral direction with a force of approximately 10 N (1 kgf, 2 lbf) to check that the clutch pedal deflection is within the service limit. If it exceeds the service limit, replace with new bushings.Deflection of the clutch pe ...