INSTRUMENTATION/DRIVER INFO (DIAGNOSTICS) > Basic Diagnostic Procedure
PROCEDURE
1. COMBINATION METER
STEP | CHECK | YES | NO |
1.PERFORM CUSTOMER INTERVIEW.
Using the Check List for Interview, ask the customer the condition of how trouble occurs. Check List for Interview > CHECK">
Did you interview the customer?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.
Interview the customer. Check List for Interview > CHECK">
2.CHECK CAN COMMUNICATION.
Read the DTC of the CAN system using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC) > OPERATION">
Is DTC displayed?
Perform the diagnosis according to the basic diagnostic procedure for LAN system. Basic Diagnostic Procedure > PROCEDURE">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.
3.CHECK COMBINATION METER.
Using the Subaru Select Monitor, read DTC of combination meter. Read Diagnostic Trouble Code (DTC)">
Is DTC displayed?
Record DTC and time stamp, and perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC) > LIST">
For time stamp, refer to “LAN SYSTEM”. General Description > CAUTION">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.
4.CHECK COMBINATION METER.
Check the operation of combination meter. System Operation Check Mode">
Is it operating normally?
System is normal.
Replace the combination meter. Combination Meter">
2. MFD
STEP | CHECK | YES | NO |
1.PERFORM CUSTOMER INTERVIEW.
Using the Check List for Interview, ask the customer the condition of how trouble occurs. Check List for Interview > CHECK">
Did you interview the customer?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.
Interview the customer. Check List for Interview > CHECK">
2.CHECK CAN COMMUNICATION.
Read the DTC of the CAN system using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC) > OPERATION">
Is DTC displayed?
Perform the diagnosis according to the basic diagnostic procedure for LAN system. Basic Diagnostic Procedure > PROCEDURE">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.
3.CHECK MFD.
Read the DTC relating the MFD using the Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is DTC displayed?
Record DTC and time stamp, and perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC) > LIST">
For time stamp, refer to “LAN SYSTEM”. General Description > CAUTION">
Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.
4.CHECK MFD.
Check the MFD display using the system operation check mode of combination meter. System Operation Check Mode">
Is the display normal?
System is normal.
Replace the MFD. Multi-function Display (MFD)">
Disarming the system
Perform either of the following procedures.
Briefly press the disarm button (for less
than 2 seconds) on the access key/remote
transmitter.
Carry the access key and perform
either of the following procedures (models
with "keyless access with push-button
start system").
Grip the front door ...
Dtc p0013 "b" camshaft position actuator control circuit/open bank 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0013 "B" CAMSHAFT POSITION ACTUATOR CONTROL CIRCUIT/OPEN BANK 1DTC detecting condition:Immediately at fault recognitionTrouble symptom:Improper idlingCAUTION:After servicing or replacing faulty part ...
Dtc c2021 tire 1 air pressure low (normal mode)
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C2021 TIRE 1 AIR PRESSURE LOW (NORMAL MODE)NOTE:Refer to DTC C2024 for diagnostic procedure. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2024 TIRE 4 AIR PRESSURE LOW ( ...