CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Basic Diagnostic Procedure
PROCEDURE
STEP | CHECK | YES | NO |
1.CHECK PRE-INSPECTION.
1) Ask the customer when and how the trouble occurred using the interview check list. Check List for Interview">
2) Before performing diagnostics, check the following items which might affect CVT problems.
• General inspection General Description > INSPECTION">
• Disconnection of harness connector
• Visual check for harness damage
• Oil leakage
• Stall speed test Stall Test">
• Secondary pressure test Secondary Pressure (Line Pressure) Test">
• Transfer clutch pressure test Transfer Clutch Pressure Test">
• Time lag test Time Lag Test">
• Road test Road Test">
• Inhibitor switch Inhibitor Switch">
Is the check result OK?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 2.
Repair the items which may be affecting the CVT trouble.
2.CHECK AT OIL TEMP LIGHT.
Turn the ignition switch to ON and wait for at least 2 seconds.
Does the AT OIL TEMP light illuminate?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 3.
Check the AT OIL TEMP light.
3.CHECK AT OIL TEMP LIGHT.
Start the engine and wait for 2 seconds or more.
Does the AT OIL TEMP light blink?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 4.
Basic Diagnostic Procedure > PROCEDURE">Go to Step 5.
4.CHECK DTC DISPLAY.
Read the DTC.
NOTE:
If the communication function of Subaru Select Monitor cannot be executed normally, check the communication circuit. Diagnostic Procedure for Subaru Select Monitor Communication > COMMUNICATION FOR INITIALIZING IMPOSSIBLE">
Is DTC displayed on Subaru Select Monitor?
Record the DTC, time stamp and freeze frame data.
Basic Diagnostic Procedure > PROCEDURE">Go to Step 6.
NOTE:
• For the time stamp, refer to LAN section. General Description > CAUTION">
• Depending on DTCs, time stamp may not be stored.
Basic Diagnostic Procedure > PROCEDURE">Go to Step 5.
5.PERFORM GENERAL DIAGNOSTICS.
1) Inspect using “Diagnostic Procedure without Diagnostic Trouble Code (DTC)”. Diagnostic Procedure without Diagnostic Trouble Code (DTC)">
2) Inspect using “Diagnostics with Phenomenon”. Diagnostics with Phenomenon">
3) Perform the Inspection Mode. Inspection Mode">
4) Read the DTC.
Is DTC displayed on Subaru Select Monitor?
Basic Diagnostic Procedure > PROCEDURE">Go to Step 6.
Finish the diagnosis.
6.PERFORM DIAGNOSIS.
1) Inspect by referring to “Diagnostic Procedure with Diagnostic Trouble Code (DTC)”. Diagnostic Procedure with Diagnostic Trouble Code (DTC)">
NOTE:
For the DTC table, refer to “List of Diagnostic Trouble Code (DTC)”. List of Diagnostic Trouble Code (DTC)">
2) Repair the trouble cause.
3) Perform the Clear Memory Mode.
4) Perform the Inspection Mode. Inspection Mode">
5) Read the DTC.
Is DTC displayed on Subaru Select Monitor?
Inspect by referring to “Diagnostic Procedure with Diagnostic Trouble Code (DTC)”. Diagnostic Procedure with Diagnostic Trouble Code (DTC)">
Finish the diagnosis.
Dtc p0963 pressure control solenoid "a" control circuit high
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0963 PRESSURE CONTROL SOLENOID "A" CONTROL CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionTrouble symptom:• Engine speed increases abruptly, and can ...
Tilt/telescopic steering wheel
WARNING
Do not adjust the steering wheel
tilt/telescopic position while driving.
This may cause loss of
vehicle control and result in
personal injury.
If the lever cannot be raised to
the fixed position, adjust the
steering wheel again. It is dangerous
to drive without locking
...
Wiring diagram
WIPER AND WASHER SYSTEMS > Wiper and Washer SystemWIRING DIAGRAM1. WIPER AND WASHER (FRONT)Refer to “Front Wiper and Washer System” in the wiring diagram. Front Wiper and Washer System > WIRING DIAGRAM">2. WIPER AND WASHER (REAR)Refer to “Rear Wiper and Washer System ...