Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Assembly

MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Main Shaft Assembly

ASSEMBLY

1. When the sleeve & hub assemblies have been disassembled, reassemble by aligning the alignment marks.

NOTE:

Position the open ends of the spring 120° apart.

(A)

3rd-4th coupling sleeve & synchronizer hub ASSY

(B)

3rd gear side

2. Install the 3rd drive gear, outer baulk ring, 3rd synchro cone, inner baulk ring, 3rd needle bearing, and sleeve & hub assembly.

NOTE:

Align the groove of the baulk ring with the 3rd-4th shifting insert.

(A)

3rd needle bearing

(B)

3rd drive gear

(C)

Inner baulk ring

(D)

3rd synchro cone

(E)

Outer baulk ring

(F)

Sleeve & hub ASSY

3. Install the 4th needle bearing race using ST1, ST2 and a press.

CAUTION:

Do not apply a load in excess of 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).

ST1 899714110REMOVER
ST2 499877000RACE 4-5 INSTALLER

(A)

4th needle bearing race

4. Install the 4th baulk ring, 4th needle bearing, 4th drive gear, and 4th gear thrust washer to the main shaft.

NOTE:

Align the 4th baulk ring and hub & sleeve assembly with the key groove.

Make sure the thrust washer is facing the correct direction.

(A)

Groove

(B)

Face this surface to the 4th gear side.

5. Press-fit the double ball bearing with ST1, ST2 and a press.

CAUTION:

Do not apply a load in excess of 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).

NOTE:

Install the snap ring side of the double ball bearing facing the 5th drive gear side.

Use a new double ball bearing.

ST1 899714110REMOVER
ST2 499877000RACE 4-5 INSTALLER

6. Using the ST1 and ST2, install the 5th gear thrust washer and 5th needle bearing race onto the rear section of the main shaft.

CAUTION:

Do not apply a load in excess of 10 kN (1 ton, 1.1 US ton, 1.0 Imp ton).

NOTE:

Make sure the thrust washer is facing the correct direction.

ST1 899714110REMOVER
ST2 499877000RACE 4-5 INSTALLER

(A)

Face this surface to the 5th gear side.

7. Install the rest of the parts to the rear section of the main shaft.

CAUTION:

Install the baulk lever so that the concave side faces toward the 5th hub.

(A)

Baulk lever

(B)

5th hub

Align the protruded section of the 5th baulk ring between the baulk levers.

(A)

5th baulk ring

(B)

Baulk lever

(C)

5th hub

8. Tighten the lock nuts to the specified torque using ST1 and ST2.

NOTE:

Use new lock nuts and lock washers.

Make sure the lock washer is installed in the proper direction.

Tightening torque:

120 N·m (12.2 kgf-m, 88.5 ft-lb)

ST1 499987003SOCKET WRENCH (35)
ST2 498937000TRANSMISSION HOLDER

(A)

5th needle bearing

(B)

5th drive gear

(C)

5th baulk ring

(D)

5th hub & sleeve No. 2

(E)

Lock washer

(F)

Lock nut

(G)

Baulk lever

(H)

Nut side

9. Crimp lock nuts in two locations after tightening.

CAUTION:

When crimping the lock nut, be careful not to crack it.

Removal
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Main Shaft AssemblyREMOVAL1. Remove the manual transmission assembly from the vehicle. Manual Transmission Assembly > REMOVAL">2. Remove the ...

Disassembly
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Main Shaft AssemblyDISASSEMBLY1. Put vinyl tape around main shaft spline to protect the oil seal from damage. Then pull out the oil seal and needle beari ...

Other materials:

Inspection
CONTROL SYSTEMS > AT Shift Lock Solenoid and “P” Range SwitchINSPECTIONSTEPCHECKYESNO1.CHECK SOLENOID UNIT.Measure the resistance of solenoid unit connector terminals.TerminalsNo. 4 — No. 3:Is the resistance 27.6 — 30.5 ?? AT Shift Lock Solenoid and “P” Range Switch &g ...

Inspection
SECURITY AND LOCKS > Keyless Access Outdoor AntennaINSPECTION1. Check the setting by performing Keyless access system check using the Subaru Select Monitor. Keyless Access System Check > OPERATION">2. Disconnect the Subaru Select Monitor. While bringing the access key, operate the tou ...

Dtc p0016 crankshaft position - camshaft position correlation bank 1 sensor a
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P0016 CRANKSHAFT POSITION - CAMSHAFT POSITION CORRELATION BANK 1 SENSOR ADTC detecting condition:Detected when two consecutive driving cycles with fault occur.Trouble symptom:• Engine stall• Improp ...

© 2016-2024 Copyright www.sucross.com