Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Assembly

DRIVE SHAFT SYSTEM > Front Drive Shaft

ASSEMBLY

1. Roll up a thick piece of paper to a size where the shaft can pass through, and affix with tape to form a cylinder.

2. Attach a new O-ring on this cylinder.

CAUTION:

Always use a new O-ring.

Be careful that the O-ring does not become scratched and that there are no foreign objects attached to it.

Make sure to install the O-ring so that it does not twist as much as possible.

Do not stretch the O-ring to 30 mm (1.18 in) inner diameter or more.

(1)

O-ring

(2)

Cylinder made with thick paper, etc.

3. Pass the cylinder material onto the shaft, and slide in the direction of the shaft axis.

(1)

Cylinder material

(2)

O-ring

(3)

Shaft

4. Clean the shaft boot groove, and wipe off the grease.

5. Slide the cylinder material near the shaft boot groove, and move the O-ring from the cylinder material onto the shaft boot groove.

CAUTION:

Attach the O-ring to the shaft boot groove center.

Be careful that the O-ring does not become scratched and that there are no foreign objects attached to it.

Make sure to install the O-ring so that it does not twist as much as possible.

With the O-ring attached, do not wash with kerosene, gasoline, etc.

(1)

Shaft

(2)

Cylinder material

(3)

O-ring

(4)

Boot groove

6. Pass the small diameter boot band through the shaft.

7. Wrap vinyl tape around the splines of the shaft.

CAUTION:

To prevent damage to the boots, make sure to always wrap with vinyl tape for protection.

8. Install a new boot (PTJ).

CAUTION:

Make sure to fit securely on the boot groove of the shaft.

(1)

Boot (PTJ)

(2)

O-ring

(3)

Boot groove

9. Match the alignment marks, and attach the trunnion onto the shaft.

10. Attach the snap ring to the shaft.

CAUTION:

Confirm that the snap ring is completely fitted in the shaft groove.

11. Fill 100 to 110 g (3.53 to 3.88 oz) of specified grease into the interior of the outer race (PTJ).

Grease:

NKG302

12. Apply a thin coat of specified grease to the roller kit and trunnion.

13. Match the alignment marks of the roller kit and trunnion, and attach the roller kit.

CAUTION:

Be careful with the roller kit position.

14. Match the alignment marks of the shaft and outer race (PTJ), and attach the outer race (PTJ).

15. Install the snap ring in the groove of the outer race (PTJ).

CAUTION:

Pull the shaft lightly and make sure that the snap ring is completely fitted in the groove.

16. Apply an even coat of the specified grease 30 to 40 g (1.06 to 1.41 oz) to the entire inner surface of boot (PTJ).

17. Attach the boot (PTJ) taking care not to twist it.

CAUTION:

Clean the large end of boot (PTJ) and the boot groove well, and remove the grease and other substances.

When installing the boot (PTJ), position the outer race (PTJ) at center of the stroke.

18. Set the new boot band at the specified position.

19. Tighten the boot bands using ST, torque wrench and socket flex handle.

CAUTION:

The large boot band is to be tightened so that the omega shaped part is at the position indicated in the figure below.

(1)

Omega shaped part

(2)

Boot band

(3)

Outer race (PTJ)

Tightening torque:

Large boot band

178 N·m (18.2 kgf-m, 131.3 ft-lb)

Small boot band

145 N·m (14.8 kgf-m, 106.9 ft-lb)

ST 28099AC000BOOT BAND PLIERS

(A)

Large boot band

(B)

Boot (PTJ)

(C)

Torque wrench

(D)

Socket flex handle

(E)

Outer race (PTJ)

20. Extend and retract the PTJ repeatedly so that grease is spread evenly.

Front drive shaft
...

Removal
DRIVE SHAFT SYSTEM > Front Drive ShaftREMOVAL1. Lift up the vehicle, and then remove the front wheels.2. Remove the axle nut.CAUTION:Do not loosen the axle nut while the front axle is loaded. Doing ...

Other materials:

Specification
CONTROL SYSTEMS > General DescriptionSPECIFICATIONItemSpecificationsSwing torque of rod against leverN (kgf, lb)3.7 (0.38, 0.83) or less ...

Installation
ENTERTAINMENT > GPS AntennaINSTALLATIONCAUTION:• After installing the center grille assembly, check that the air vent grille of the center grille assembly is inserted correctly into the air vent duct.• Before handling the airbag system components, always refer to “CAUTION” ...

Installation
AIRBAG SYSTEM > Curtain Airbag ModuleINSTALLATIONCAUTION:• Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">• When installing the curtain airbag ...

© 2016-2024 Copyright www.sucross.com