Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Assembly

CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reverse Brake Assembly

ASSEMBLY

1. Install the reverse brake piston.

NOTE:

Apply CVTF to the sealing area of reverse brake piston.

2. Install the return spring.

3. Install the spring retainer.

4. Compress the return spring using the ST to install the snap ring.

ST1 18762AA001COMPRESSOR SPECIAL TOOL

5. Check the operation of reverse brake piston by blowing compressed air intermittently from reverse brake housing hole.

6. Place the driven plate, drive plate and retaining plate neatly in this order on surface table.

7. Set the dial gauge to retaining plate, and read its scale.

NOTE:

The value, which is read in the gauge at this time, is zero point.

8. Scale and record the weight “Z” of a flat board which will be put on retaining plate.

NOTE:

Use a stiff board which does not bend against load as a flat board to be put on retaining plate.

Use a flat board weighing less than 29 N (3.0 kgf, 6.5 lb).

9. Put the flat board on retaining plate.

10. Using the following formula, read the push/pull gauge and calculate “N”.

N = 29 N (3.0 kgf, 6.5 lb) − Z

29 N (3.0 kgf, 6.5 lb): Load applied to clutch plate

Z: Flat board weight

11. Press the center of retaining plate by applying a force of “N” using push/pull gauge, and then measure and record the compression amount “A”.

NOTE:

Measure at four points with a 90° interval and calculate the average.

(A)

Drive plate

(B)

Driven plate

(C)

Retaining plate

12. Install the dish plate, drive plate, driven plate, retaining plate and snap ring to the reverse brake housing.

NOTE:

Install the dish plate in the correct direction.

13. Measure and record the clearance “B” between the retaining plate and snap ring.

14. Piston stroke calculation

Calculate with A and B dimensions recorded before. If it exceeds the limit, replace with a new drive plate and adjust within the initial standard value.

S mm (in) = A + B

S: Piston stroke

A: Compression amount of drive plate and dish plate

B: Clearance between retaining plate and snap ring

Initial standard:

2.3 — 2.7 mm (0.091 — 0.106 in)

Limit thickness:

2.9 mm (0.114 in)

Retaining plate

Part No.

Thickness mm (in)

31567AB750

4.2 (0.165)

31567AB800

4.4 (0.173)

31567AB810

4.6 (0.181)

31567AB820

4.8 (0.189)

Reverse brake assembly
...

Removal
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reverse Brake AssemblyREMOVAL1. Remove the transmission assembly from the vehicle. Automatic Transmission Assembly > REMOVAL">2. Remove the a ...

Other materials:

Installation
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Shifter Fork and RodINSTALLATION1. Install the check ball spring and check ball to the reverse fork rod arm, and press in the ST.ST 399411700ACCENT BALL INSTALLER2. Install the reverse fork rod through the hole on the rear of the transmission case. P ...

Removal
SECURITY AND LOCKS > IG Relay2 (Push Button Start)REMOVALCAUTION:Before handling the airbag system components, refer to “CAUTION” of “General Description” in “AIRBAG SYSTEM”. General Description > CAUTION">1. Disconnect the ground cable from battery ...

Hill start assist warning light/Hill start assist OFF indicator light
Hill start assist warning light While the engine is running, if there are any malfunctions in the Hill start assist system, the warning light will illuminate. WARNING When the Hill start assist warning light illuminates, have the vehicle inspected at an authorized SUBARU dealer. Hill st ...

© 2016-2022 Copyright www.sucross.com