Subaru Crosstrek Service Manual: Adjustment
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Drive Pinion Shaft Assembly
ADJUSTMENT
1. THRUST BEARING PRELOAD
1. Select a suitable adjusting washer No. 1 so that dimension (H) will be zero in a visual check. Position the washer (18.3 ? 30 ? t) and lock washer (18 ? 30 ? 2) and attach the lock nut.
2. Using the ST1, ST2 and ST3, tighten the lock nut to the specified torque.
NOTE:
• Use new lock nuts and lock washers.
• Make sure the lock washer is installed in the proper direction.
Tightening torque:
120 N·m (12.2 kgf-m, 88.5 ft-lb)
| ST1 899884100 | HOLDER |
| ST2 498427100 | STOPPER |
| ST3 899988608 | SOCKET WRENCH (27) |
(A) | Lock nut |
(B) | Lock washer |
(C) | Washer |
(D) | Nut side |
3. After removing the ST2, measure the starting torque using torque driver.
Starting torque:
0.3 — 0.8 N·m (0.03 — 0.08 kgf-m, 0.22 — 0.59 ft-lb)
| ST1 899884100 | HOLDER |
| ST3 899988608 | SOCKET WRENCH (27) |
4. If the starting torque is not within the specified limit, select new adjusting washer No. 1 and recheck starting torque.
(A) | Adjusting washer No. 1 |
(B) | Adjusting washer No. 2 |
Adjusting washer No. 1 | |
Part No. | Thickness mm (in) |
803025051 | 3.925 (0.1545) |
803025052 | 3.950 (0.1555) |
803025053 | 3.975 (0.1565) |
803025054 | 4.000 (0.1575) |
803025055 | 4.025 (0.1585) |
803025056 | 4.050 (0.1594) |
803025057 | 4.075 (0.1604) |
5. If the specified starting torque cannot be obtained by the selection of adjusting washer No. 1, select adjusting washer No. 2 from the list below. Repeat steps 1) through 4) to adjust starting torque.
(A) | Adjusting washer No. 1 |
(B) | Adjusting washer No. 2 |
Starting torque | Dimension H | Adjusting washer No. 2 |
Low | Small | Select thicker one. |
High | Large | Select thinner one. |
Adjusting washer No. 2 | |
Part No. | Thickness mm (in) |
803025059 | 3.850 (0.1516) |
803025054 | 4.000 (0.1575) |
803025058 | 4.150 (0.1634) |
6. Recheck that the starting torque is within the specified range, then crimp the lock nut at four positions.
CAUTION:
When crimping the lock nut, be careful not to crack it.
Removal
MANUAL TRANSMISSION AND DIFFERENTIAL(5MT) > Drive Pinion Shaft AssemblyREMOVAL1. Remove the manual transmission assembly from the vehicle. Manual Transmission Assembly > REMOVAL">2. Rem ...
Other materials:
Reclining the seatback
Pull the reclining lever up and adjust the
seatback to the desired position. Then
release the lever and make sure the
seatback is securely locked into place.
The seatback placed in a reclined position
can spring back upward with force when
the lever is pulled. While operating the
lever ...
Disassembly
REAR SUSPENSION > Rear Trailing LinkDISASSEMBLY1. BUSHING A - TRAILING LINKUsing the ST, push out the bushing A - trailing link.Preparation tool:ST-A: INSTALLER (899874100)ST-B: INSTALLER & REMOVER (BASE) (20099PA010)2. BUSHING - TRAILING LINKFor the removal procedure of bushing - trailing li ...
Dtc c2531 control module cpu
POWER ASSISTED SYSTEM (POWER STEERING) (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C2531 CONTROL MODULE CPUTROUBLE SYMPTOM:• The steering wheel operation feels heavy.• STEERING warning light illuminates.NOTE:When this code is displayed, replace the power ...
