Subaru Crosstrek Service Manual: Adjustment
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reduction Drive Gear
ADJUSTMENT
1. Remove the retaining springs and reduction drive gear shims.
2. Install the transmission case, and secure it with four or five bolts.
Tightening torque:
22 N·m (2.2 kgf-m, 16.2 ft-lb)
3. Measure depth “A” from the ST upper face to the reduction drive gear end face.
| ST 499575400 | GAUGE |
4. Raise and hold the reduction drive gear.
5. Measure depth “B” from the ST upper face to the reduction drive gear end face.
| ST 499575400 | GAUGE |
6. Calculate the following formula.
T mm = A − B − 1.0
[T in = A − B − 0.039]
T: Moving distance of reduction drive gear shim
A: Depth from the ST upper face to the reduction drive gear end surface
B: Depth from the ST upper face to the reduction drive gear end surface
1.0 mm (0.039 in): Thickness of spring retainer
Moving distance of transfer drive gear [T] | Total shim thickness mm (in) |
0.420 — 0.519 (0.0165 — 0.0204) | 0.3 (0.012) |
0.520 — 0.619 (0.0205 — 0.0242) | 0.4 (0.016) |
0.620 — 0.719 (0.0244 — 0.0283) | 0.5 (0.020) |
0.720 — 0.819 (0.0283 — 0.0322) | 0.6 (0.024) |
0.820 — 0.919 (0.0323 — 0.0362) | 0.7 (0.028) |
0.920 — 1.019 (0.0362 — 0.0401) | 0.8 (0.031) |
1.020 — 1.119 (0.0402 — 0.0441) | 0.9 (0.035) |
1.120 — 1.219 (0.0441 — 0.0480) | 1.0 (0.039) |
1.220 — 1.319 (0.0480 — 0.0519) | 1.1 (0.043) |
1.320 — 1.419 (0.0520 — 0.0559) | 1.2 (0.047) |
1.420 — 1.519 (0.0559 — 0.0598) | 1.3 (0.051) |
1.520 — 1.619 (0.0598 — 0.0637) | 1.4 (0.055) |
1.620 — 1.719 (0.0638 — 0.0677) | 1.5 (0.059) |
1.720 — 1.819 (0.0677 — 0.0716) | 1.6 (0.063) |
1.820 — 1.920 (0.0717 — 0.0756) | 1.7 (0.067) |
7. Select one to three reduction drive gear shims so that the total thickness meets the value obtained from step 6).
Part No. | Reduction drive gear shim thickness mm (in) |
31288AA260 | 0.3 (0.012) |
31288AA270 | 0.4 (0.016) |
31288AA280 | 0.5 (0.020) |
31288AA290 | 0.6 (0.024) |
Removal
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Reduction Drive GearREMOVAL1. Remove the transmission assembly from the vehicle. Automatic Transmission Assembly > REMOVAL">2. Remove the air ...
Other materials:
Installation
FUEL INJECTION (FUEL SYSTEMS)(H4DO) > Engine Control Module (ECM)INSTALLATIONInstall in the reverse order of removal.CAUTION:• When the ECM of model with immobilizer has been replaced, be sure to perform the registration of immobilizer system.• For model without keyless access with pu ...
Installation
EXTERIOR BODY PANELS > Door Sash TapeINSTALLATIONCAUTION:• Do not reuse the removed door sash tape. Replace it with a new tape.• Press evenly along the sash when applying the tape using a spatula or similar object to make sure no bubbles are formed.If air bubbles are formed, reapply t ...
Dtc b1821 open in side airbag rh
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC B1821 OPEN IN SIDE AIRBAG RHDiagnosis start condition:Ignition voltage is 10 V to 16 V.DTC detecting condition:• Side airbag harness (RH) circuit is open.• Side airbag module (RH) is faulty.• Airbag control modu ...
