Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: 14

CRUISE CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Cancel Code

14

Detected when select lever is set in the neutral position, or when malfunction related to neutral position switch occurs.

TROUBLE SYMPTOM:

Cruise control cannot be set.

WIRING DIAGRAM:

Cruise control system Cruise Control System > WIRING DIAGRAM">

STEPCHECKYESNO

1.CHECK TRANSMISSION TYPE.

Is the transmission type CVT?

Diagnostic Procedure with Cancel Code > 14">Go to Step 2.

Diagnostic Procedure with Cancel Code > 14">Go to Step 5. (MT model)

2.CHECK INHIBITOR SWITCH CIRCUIT.

1) Turn the ignition switch to OFF.

2) Disconnect the inhibitor switch harness connector.

3) Turn the ignition switch to ON.

4) Measure the voltage between harness connector terminal and chassis ground.

Connector & terminal

(T7) No. 6 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Cancel Code > 14">Go to Step 3.

Check for open or short in the harness between inhibitor switch and ECM.

3.CHECK INHIBITOR SWITCH CIRCUIT.

1) Turn the ignition switch to OFF.

2) Disconnect the starter motor harness connector.

3) Measure the resistance between inhibitor switch harness connector terminal and starter motor.

Connector & terminal

(T7) No. 9 — Starter motor:

Is the resistance less than 10 ??

Diagnostic Procedure with Cancel Code > 14">Go to Step 4.

Repair the harness.

4.CHECK INHIBITOR SWITCH.

Remove and check the inhibitor switch. Inhibitor Switch">

Is the inhibitor switch working normal?

Replace the ECM.
Engine Control Module (ECM)">

Replace the inhibitor switch.

5.CHECK NEUTRAL POSITION SWITCH CIRCUIT.

1) Turn the ignition switch to OFF.

2) Disconnect the neutral position switch harness connector.

3) Turn the ignition switch to ON.

4) Measure the voltage between harness connector terminal and chassis ground.

Connector & terminal

(B25) No. 2 (+) — Chassis ground (−):

Is the voltage 10 V or more?

Diagnostic Procedure with Cancel Code > 14">Go to Step 6.

Check for open or short in the harness between neutral position switch and ECM.

6.CHECK NEUTRAL POSITION SWITCH CIRCUIT.

1) Turn the ignition switch to OFF.

2) Measure resistance between harness connector terminal of neutral position switch and chassis ground.

Connector & terminal

(B25) No. 1 — Chassis ground:

Is the resistance less than 10 ??

Diagnostic Procedure with Cancel Code > 14">Go to Step 7.

Repair the harness.

7.CHECK NEUTRAL POSITION SWITCH.

Remove and check the neutral position switch. Neutral Position Switch">

Is the neutral position switch OK?

Replace the ECM.
Engine Control Module (ECM)">

Replace the neutral position switch.

13
CRUISE CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Cancel Code13Detected when clutch pedal is depressed or malfunction related to clutch switch occurs.TROUBLE SYMPTOM:• Cruise co ...

15
CRUISE CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Cancel Code15Detected when CANCEL switch is pressed or malfunction related to CRUISE switch occurs.TROUBLE SYMPTOM:• Cruise con ...

Other materials:

Installation
CONTINUOUSLY VARIABLE TRANSMISSION(TR580) > Turbine Speed SensorINSTALLATIONCAUTION:Be sure to prevent water or oil from contacting the connector terminal of turbine speed sensor. If adhesion occurs, replace with a new part.Install in the reverse order of removal.NOTE:• Use new O-rings.&bul ...

Caution
CONTINUOUSLY VARIABLE TRANSMISSION (DIAGNOSTICS) > General DescriptionCAUTION1. The airbag system wiring harness is routed near the TCM.CAUTION:• All the airbag system wiring harnesses and connectors are colored yellow. Do not use an electric test equipment to check these circuits.• B ...

Driving tips
Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill on an upgrade. Either of those actions may cause clutch damage. Do not drive with your hand resting on the shift lever. This may cause wear on the transmission components. ...

© 2016-2022 Copyright www.sucross.com