Subaru Crosstrek Service Manual: Dtc c0064 normal closing valve 2 malfunction

DTC detecting condition:

• Defective harness connector

• Defective VDCH/U solenoid valve

• ABS does not operate.

• EBD does not operate.

• VDC does not operate.

• EyeSight does not operate.

1.CHECK VDCCM&H/U INPUT VOLTAGE.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from the VDCCM&H/U.

3) Run the engine at idle.

4) Measure the voltage between VDCCM&H/U connector and chassis ground.

Connector & terminal

(B310) No. 1 (+) — Chassis ground (−):

(B310) No. 14 (+) — Chassis ground (−):

(B310) No. 20 (+) — Chassis ground (−):

Is the voltage 10 — 15 V?

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0064 NORMAL CLOSING VALVE 2 MALFUNCTION">Go to Step 2.

Repair the power supply circuit including the battery.

2.CHECK VDCCM&H/U GROUND CIRCUIT (CHECK FOR OPEN CIRCUIT).

1) Turn the ignition switch to OFF.

2) Measure the resistance between VDCCM&H/U connector and chassis ground.

Connector & terminal

(B310) No. 26 — Chassis ground:

Is the resistance less than 10 ??

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0064 NORMAL CLOSING VALVE 2 MALFUNCTION">Go to Step 3.

Repair the VDCCM&H/U ground harness.

3.CHECK POOR CONTACT OF CONNECTORS.

Is there poor contact of connector between generator, battery and VDCCM&H/U?

Repair the connector.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0064 NORMAL CLOSING VALVE 2 MALFUNCTION">Go to Step 4.

4.CHECK VDCCM&H/U.

1) Connect all connectors.

2) Perform the Clear Memory Mode. Clear Memory Mode">

3) Perform the Inspection Mode. Inspection Mode">

4) Read the DTC. Read Diagnostic Trouble Code (DTC)">

Is the same DTC displayed?

Replace the VDCCM&H/U. VDC Control Module and Hydraulic Control Unit (VDCCM&H/U)">

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C0064 NORMAL CLOSING VALVE 2 MALFUNCTION">Go to Step 5.

5.CHECK DETECTION OF OTHER DTCS FOR VDC.

Read Diagnostic Trouble Code (DTC)">

Is any other DTC displayed?

Perform the diagnosis according to DTC. List of Diagnostic Trouble Code (DTC)">

Currently, it is normal. There may have been a temporary poor contact in the harness and connector or a temporary noise interference.

Dtc c0063 normal closing valve 1 malfunction

Dtc c0041 ecm

Other materials:

Dtc b28a1 eyesight communication(ecm)
EyeSight (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B28A1 EyeSight COMMUNICATION(ECM)Detected when the engine control module (ECM) detects the malfunction of stereo camera, or when the stereo camera or ECM is assembled incorrectly.DTC DETECTING CONDITION:• De ...

Dtc p1531 battery current sensor circuit high
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P1531 BATTERY CURRENT SENSOR CIRCUIT HIGHDTC detecting condition:Immediately at fault recognitionCAUTION:After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION&q ...

Driving tips for AWD models
WARNING Always maintain a safe driving speed according to the road and weather conditions in order to avoid having an accident on a sharp turn, during sudden braking or under other similar conditions. Always use the utmost care in driving - overconfidence because you are driving ...