Subaru Crosstrek manuals

Subaru Crosstrek Owners Manual: Seatbelt warning light and chime

Your vehicle is equipped with a seatbelt warning device at the driver's and front passenger's seat, as required by current safety standards.

With the ignition switch turned to the "ON" position, this device reminds the driver and front passenger to fasten their seatbelts by illuminating the warning lights in the locations indicated in the following illustration and sounding a chime.

Driver's warning light (type A)
Driver's warning light (type A)

Driver's warning light (type B)
Driver's warning light (type B)

Front passenger's warning light
Front passenger's warning light

Operation

If the driver and/or front passenger have/ has not yet fastened the seatbelt(s) when the ignition switch is turned to the "ON" position, the seatbelt warning light(s) will flash for 6 seconds, to warn that the seatbelt(s) is/are unfastened. If the driver's seatbelt is not fastened, a chime will also sound simultaneously.

NOTE

If the driver's and/or front passenger's seatbelt(s) are/is still not fastened 6 seconds later, the seatbelt warning device operates as follows according to the vehicle speed.

It is possible to cancel the warning operation that follows the 6-second warning after turning ON the ignition switch. When the ignition switch is turned ON next time, however, the complete sequence of the warning operation resumes. For further details about canceling the warning operation, please contact your SUBARU dealer.

If there is no passenger on the front passenger's seat, the seatbelt warning device for the front passenger's seat will be deactivated. The front passenger's occupant detection system monitors whether or not there is a passenger on the front passenger's seat.

Observe the following precautions. Failure to do so may prevent the device from functioning correctly or cause the device to fail.

If the seatbelt warning device for the front passenger's seat does not function correctly (e.g., it is activated even when the front passenger's seat is empty or it is deactivated even when the front passenger has not fastened his/her seatbelt), take the following actions.

If still the seatbelt warning device for front passenger's seat does not function correctly after taking relevant corrective actions described above, immediately contact your SUBARU dealer for an inspection.

Initial illumination for system check
Several of the warning and indicator lights illuminate when the ignition switch is initially turned to the "ON" position. This permits checking the operation of the bulbs. Apply the parking bra ...

SRS airbag system warning light
WARNING If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag system. Immediately take your vehicle to your ...

Other materials:

Inspection
VEHICLE DYNAMICS CONTROL (VDC) > VDC OFF SwitchINSPECTION1. Disconnect the VDC OFF switch connector.2. Check the resistance between the VDC OFF switch terminals.PREPARATION TOOL:Circuit testerTerminal No.Inspection conditionsStandard2 — 3Switch OFF1 M? or moreSwitch ONLess than 1 ?3. Replace th ...

Inspection
SEAT BELT SYSTEM > Front Seat BeltINSPECTION1. VISUAL INSPECTIONCheck for the following, and replace with new parts if necessary.• Pretensioner is cracked or deformed.• Adjuster assembly - seat belt is cracked or deformed.• Seat belt is slackened, bent or worn.• Seat belt ...

Dtc p2195 a/f /o2 sensor signal biased/stuck lean bank 1 sensor 1
ENGINE (DIAGNOSTICS)(H4DO) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC P2195 A/F /O2 SENSOR SIGNAL BIASED/STUCK LEAN BANK 1 SENSOR 1DTC detecting condition:Detected when two consecutive driving cycles with fault occur.CAUTION:After servicing or replacing faulty parts, perform Cle ...

© 2016-2019 Copyright www.sucross.com