Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Installation

WIPER AND WASHER SYSTEMS > Front Wiper Arm

INSTALLATION

1. MODELS WITHOUT EyeSight

1. Install the arm assembly - windshield wiper.

(1) Assemble the arm assembly - windshield wiper so that the blade assembly - windshield wiper is aligned to the ceramic print point mark of the windshield glass.

(2) Tighten the arm assembly - windshield wiper to specified torque and install the cap.

Tightening torque:

26 N·m (2.65 kgf-m, 19.2 ft-lb)

2. Operate the windshield wiper to check that the stop position is aligned with the point mark.

If it is not aligned with the point mark, perform the removal and installation of the windshield wiper over again. Front Wiper Arm > REMOVAL">

2. MODELS WITH EyeSight

CAUTION:

Install firmly so that the hose is not bent, compressed or flattened.

1. When the hose is removed from the joint ­ washer hose, refer to “Installation” of “Front washer nozzle & hose”. Front Washer Nozzle and Hose > INSTALLATION">

2. Install the arm assembly - windshield wiper.

(1) Align the alignment mark (a), and install the hose to the arm assembly - windshield wiper assistor.

(2) Assemble the arm assembly - windshield wiper so that the blade assembly - windshield wiper is aligned to the ceramic print point mark of the windshield glass.

(3) Tighten the arm assembly - windshield wiper to specified torque and install the cap.

Tightening torque:

26 N·m (2.65 kgf-m, 19.2 ft-lb)

3. Operate the windshield wiper to check that the stop position is aligned with the point mark.

If it is not aligned with the point mark, perform the removal and installation of the windshield wiper over again. Front Wiper Arm > REMOVAL">

4. Make sure that there is a gap of 1 mm (0.04 in) or more between the hose and the cover ­ joint and between the hose and the joint ­ washer hose during windshield wiper operation.

(A)

Gap between hose and cover ­ joint outer side

(C)

Gap between hose and cover ­ joint inner side

(D)

Gap between hose and cover ­ joint lower side

(B)

Gap between hose and cover ­ joint upper side

Removal
WIPER AND WASHER SYSTEMS > Front Wiper ArmREMOVAL1. MODELS WITHOUT EyeSight1. Remove the cover - windshield wiper arm.2. Remove the nuts, and remove the arm assembly - windshield wiper.2. MODELS WI ...

Front wiper motor and link
...

Other materials:

22
CRUISE CONTROL SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Cancel Code22Malfunction related to vehicle speed sensor is detected.DIAGNOSIS:Open or shorted circuit in vehicle speed sensor system.TROUBLE SYMPTOM:Cruise control cannot be set. (Cancelled immediately.)STEPCHECKYESNO1.CHECK ABS OR ...

Dtc u0420 invalid data received from power steering control module
LAN SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC U0420 INVALID DATA RECEIVED FROM POWER STEERING CONTROL MODULEDTC DETECTING CONDITION:Defective data was transmitted from EPS CM.TROUBLE SYMPTOM:Cooperation control with EPS CM does not operate properly.STEPCHEC ...

Installation
LIGHTING SYSTEM > Headlight BulbINSTALLATIONCAUTION:Install so that the front end of the under cover (b) comes inside the bumper face - front (a), and the front end of the mud guard (c) comes outside the bumper face - front (a).1. Install each part in the reverse order of removal.2. When performi ...

© 2016-2020 Copyright www.sucross.com