Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Installation

EyeSight > Stereo Camera

INSTALLATION

CAUTION:

Do not remove the protective cover until just before installing the stereo camera cover assembly. Using the bolt and nut, install the stereo camera with the protective cover attached, connect the connectors, and then remove the protective cover.

Do not apply any impact to the stereo camera. (Even the slightest shock will deviate the optical axis of the camera, resulting in the loss of normal operation of the camera.)

During installation, do not hold at the left and right cameras.

Do not change the installation position of the stereo camera or do not modify the surrounding structure.

Remove the protective cover, install the stereo camera cover assembly, and then perform adjustment and inspection of the stereo camera. Camera Adjustment, Inspection">

Do not touch the lens filter on the stereo camera. If touched, replace the stereo camera.

When installing the stereo camera cover assembly, cover with dust-free paper such as copy paper to avoid interference with the lens filter section, and attach the paper using tape while being careful not to let the adhesive surface contact the glass surface. Be sure to remove the paper after the procedure.

Also, do not put your hand on the polyurethane section of the windshield contact surface. Doing so may cause the polyurethane section to be removed, which may interfere with the normal operation if it hangs down in front of the lens filter section.

When installing the stereo camera cover assembly, take care so that the harness does not interfere with the stereo camera or does not get caught.

Do not allow the stereo camera cover assembly to come in contact with the stereo camera. Install the stereo camera cover assembly precisely so that it will not block the visibility of the camera.

Because the stereo camera is incompatible, be sure to check the part number before installation.

1. Attach the camera plate.

Tightening torque:

5.5±1.0 N·m (0.56±0.10 kgf-m, 4.1±0.7 ft-lb)

NOTE:

Align the positioning pins of camera plate to the positioning holes of front rail.

2. Install the stereo camera.

Tightening torque:

5.5±1.0 N·m (0.56±0.10 kgf-m, 4.1±0.7 ft-lb)

NOTE:

Align the positioning holes of stereo camera to the positioning pins of camera plate.

3. Install the stereo camera cover assembly.

4. Connect the battery ground terminal. NOTE">

5. Perform the adjustment or inspection of the stereo camera. Camera Adjustment, Inspection">

Stereo camera
...

Removal
EyeSight > Stereo CameraREMOVALCAUTION:• When the stereo camera or windshield glass has been replaced, removed or installed, always perform the adjustment and inspection of the camera. (When ...

Other materials:

Electrical component location Location
AIRBAG SYSTEM (DIAGNOSTICS) > Electrical Component LocationLOCATION(1)Front sub sensor (RH)(11)Side airbag sensor (RH)(20)Satellite safing sensor(2)Front sub sensor (LH)(12)Seat belt pretensioner (LH)(21)Occupant detection control module(3)Airbag control module(13)Seat belt pretensioner (RH)(22)B ...

Operation
SECURITY AND LOCKS > Impact SensorOPERATION1. IMPACT SENSOR SETTING USING SUBARU SELECT MONITOR1. Make an impact sensor setting.(1) Connect the Subaru Select Monitor.NOTE:For detailed operation procedures, refer to “Application help”.(2) Turn the ignition switch to ON.(3) On «Start» ...

Dtc u0073 control module communication bus off
AIRBAG SYSTEM (DIAGNOSTICS) > Diagnostic Chart with Trouble CodeDTC U0073 CONTROL MODULE COMMUNICATION BUS OFFDiagnosis start condition:Ignition voltage remains at 10 V or more for 1 second.DTC detecting condition:Detected when malfunction occurs in CAN line.NOTE:Perform the diagnosis for LAN sys ...

© 2016-2024 Copyright www.sucross.com