Subaru Crosstrek Service Manual: Operation

1. SUBARU STARLINK CONNECTION ID DISPLAY

Model with 6.2 inch display

1. Turn the ignition switch to ACC.

2. Press the HOME button (a) to display the {HOME} screen.

3. Touch the {SETTINGS} (b) to display the {SETTINGS} screen.

4. Touch the {Settings General} (c) to display the {Settings General} screen.

5. Touch the {Version} (d) in {System Software}.

6. Confirm the Serial Number (8 digits).

Model with 7 inch display

Operation is the same as that of navigation assembly, therefore, refer to “Navigation System”. Navigation System > OPERATION">

Model with 6.2 inch display

1. Perform the same procedure as for the SUBARU STARLINK connection ID display. Audio System > OPERATION">

2. Confirm the Software Ver.

Model with 7 inch display

Operation is the same as that of navigation assembly, therefore, refer to “Navigation System”. Navigation System > OPERATION">

Model with 6.2 inch display

1. Turn the ignition switch to ACC.

2. Press the HOME button (a) to display the {HOME} screen.

3. Touch the {SETTINGS} (b) to display the {SETTINGS} screen.

4. Touch the {Settings General} (c) to display the {Settings General} screen.

5. Touch the {Restore} (d) in {Reset to Factory Settings}.

6. Touch {OK} after {Are you sure you want to delete All Data?} is displayed.

7. {DO NOT OPERATE. Initializing now.} is displayed, and all data deletion is initiated.

8. When all data is deleted, {All date has been deleted. Start up the engine to reboot.} is displayed.

Model with 7 inch display

Operation is the same as that of navigation assembly, therefore, refer to “Navigation System”. Navigation System > OPERATION">

Model with 6.2 inch display

1. Turn the ignition switch to ACC.

2. Press the button (a) to display the Audio OFF screen.

3. Touch the screen in order from (b) to (e).

Pressing the button (a) or turning the ignition switch from the OFF to ACC position can exit the Line Diag mode.

4. {Line Diag} screen is displayed.

5. Check the connection status with the {Connectivity Check} in the {Line Diag} screen.

Check the external connection terminals (USB 1, 2 and AUX) by connecting a memory for check or a pin jack.

Model with 7 inch display

Operation is the same as that of navigation assembly, therefore, refer to “Navigation System”. Navigation System > OPERATION">

Model with 6.2 inch display

1. Turn the ignition switch to ACC.

2. Press the button (a) to display the Audio OFF screen.

3. Touch the screen in order from (b) to (e).

Pressing the button (a) or turning the ignition switch from the OFF to ACC position can exit the diagnostic mode.

4. {Line Diag} screen is displayed.

5. Check the connection status with the {Vehicle Signal Check} in the {Line Diag} screen.

• Check illumination

NOTE:

Make sure that the bright switch is not ON.

1. Set the lighting switch to the parking position.

2. Make sure that {OK} lights in ILL+ and then the screen becomes dim.

OK: Normal.

NG: Abnormal. Check the signal line connector. If there are no problems, the unit could be faulty.

– Before starting inspections, check the safety around the vehicle.

– Lift up the vehicle as necessary.

– When the diagnostic trouble code is input in the VDC CM, perform the Clear Memory Mode.

1. Drive the vehicle at 8 km/h (5 MPH) or more.

2. Check that {OK} is displayed in SPD.

OK: Normal.

NG: Vehicle speed is less than 8 km/h (5 MPH), or malfunction is detected in the signal line. Check the signal line connector. If there are no problems, the unit could be faulty.

1. Pull parking brake lever.

2. Check that {OK} is displayed in PKB.

OK: Normal.

NG: Abnormal. Check the signal line connector. If there are no problems, the unit could be faulty.

Before starting inspections, check the safety behind the vehicle.

1. Turn the ignition to ON.

2. Pull the parking brake lever and depress the brake pedal, then place the select lever or gear shift lever in reverse.

3. Make sure that {OK} is displayed in REV.

OK: Normal.

NG: Abnormal. Check the signal line connector. If there are no problems, the unit could be faulty.

Model with 7 inch display

Operation is the same as that of navigation assembly, therefore, refer to “Navigation System”. Navigation System > OPERATION">

Model with 6.2 inch display

1. Turn the ignition switch to ACC.

2. Press the button (a) to display the Audio OFF screen.

3. Touch the screen in order from (b) to (e).

Pressing the button (a) or turning the ignition switch from the OFF to ACC position can exit the Line Diag mode.

4. {Line Diag} screen is displayed.

5. Touch {Audio Check} on the {Line Diag} screen.

6. {Audio Check} screen is displayed.

7. Touch the {ON} key of {Speaker Check} to check speaker output.

NOTE:

• The speaker front left > front right > rear right > rear left will sound in order for 2 seconds each.

• The speaker sounds at the maximum volume during speaker check.

• Press the {BACK} key to return to the {Line Diag} screen.

Model with 7 inch display

Operation is the same as that of navigation assembly, therefore, refer to “Navigation System”. Navigation System > OPERATION">

• Displayed only for model with 6.2 inch display.

• Some items are not displayed according to destination.

1. Turn the ignition switch to ACC.

2. Press the button (a) to display the Audio OFF screen.

3. Touch the screen in order from (b) to (e).

Pressing the button (a) or turning the ignition switch from the OFF to ACC position can exit the Line Diag mode.

4. {Line Diag} screen is displayed.

5. Touch {Dealer Diag} on the {Line Diag} screen.

6. The {Dealer Diag} screen is displayed.

7. Touch the {9kHz} or {10kHz} key to switch the AM radio frequency range.

• When the setting is changed, reboot confirmation for frequency switch-over is displayed. Select {OK} to reboot. When {cancel} is pressed, the {Dealer Diag} screen is displayed.

• The initial settings is at 9 kHz.

Note

Data communication module

Other materials:

Light control and wiper control levers/switches
Windshield wiper Mist Windshield washer Rear window wiper and washer switch Wiper intermittent time control switch Wiper control lever Light control switch Fog light switch Headlight ON/OFF/AUTO Headlight flasher High/Low beam Turn signal lever ...

Removal
LIGHTING SYSTEM > Headlight AssemblyREMOVALCAUTION:• Do not perform work with wet hands, because there is a possibility of electrical shock.• The HID type uses very high voltages for the lighting circuit. Make sure that the power supply is turned OFF before working.1. Disconnect the g ...

Command list
Recognizable voice commands and their actions are shown below. NOTE Some voice commands may not be available depending on the market, vehicle specifications or the device connection status. Frequently used commands are listed in the following tables. For devices that are not instal ...