Subaru Crosstrek Service Manual: Fuel injector circuit

CAUTION:

• Check or repair only faulty parts.

• After servicing or replacing faulty parts, perform Clear Memory Mode Clear Memory Mode > OPERATION">, and Inspection Mode Inspection Mode > PROCEDURE">.

1.CHECK OPERATION OF EACH FUEL INJECTOR.

While cranking the engine, check each fuel injector emits operating sound. Use a sound scope or attach a screwdriver to the injector to listen to sounds for this check.

Does the fuel injector emit operating sound?

Check the fuel pressure. Fuel Pressure > INSPECTION">

Diagnostics for Engine Starting Failure > FUEL INJECTOR CIRCUIT">Go to Step 2.

2.CHECK POWER SUPPLY TO EACH FUEL INJECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from fuel injector.

3) Turn the ignition switch to ON.

4) Measure the power supply voltage between fuel injector terminal and engine ground.

Connector & terminal

#1 (E5) No. 2 (+) — Engine ground (−):

#2 (E16) No. 2 (+) — Engine ground (−):

#3 (E6) No. 2 (+) — Engine ground (−):

#4 (E17) No. 2 (+) — Engine ground (−):

Is the voltage 10 V or more?

Diagnostics for Engine Starting Failure > FUEL INJECTOR CIRCUIT">Go to Step 3.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between main relay connector and fuel injector connector

• Poor contact of main relay connector

• Poor contact of coupling connector

3.CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTOR.

1) Turn the ignition switch to OFF.

2) Disconnect the connector from ECM.

3) Measure the resistance of harness between ECM connector and fuel injector connector.

Connector & terminal

#1 (B134) No. 12 — (E5) No. 1:

#2 (B134) No. 22 — (E16) No. 1:

#3 (B134) No. 32 — (E6) No. 1:

#4 (B134) No. 13 — (E17) No. 1:

Is the resistance less than 1 ??

Diagnostics for Engine Starting Failure > FUEL INJECTOR CIRCUIT">Go to Step 4.

Repair the harness and connector.

NOTE:

In this case, repair the following item:

• Open circuit in harness between ECM connector and fuel injector connector

• Poor contact of coupling connector

4.CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTOR.

Measure the resistance between ECM connector and chassis ground.

Connector & terminal

#1 (B134) No. 12 — Chassis ground:

#2 (B134) No. 22 — Chassis ground:

#3 (B134) No. 32 — Chassis ground:

#4 (B134) No. 13 — Chassis ground:

Is the resistance 1 M? or more?

Diagnostics for Engine Starting Failure > FUEL INJECTOR CIRCUIT">Go to Step 5.

Repair the short circuit to ground in harness between ECM connector and fuel injector connector.

5.CHECK EACH FUEL INJECTOR.

Measure the resistance between each fuel injector terminals.

Terminals

No. 1 — No. 2:

Is the resistance 5 — 20 ??

Diagnostics for Engine Starting Failure > FUEL INJECTOR CIRCUIT">Go to Step 6.

Replace the faulty fuel injector. Fuel Injector">

6.CHECK FOR POOR CONTACT.

Check for poor contact of ECM connector.

Is there poor contact of ECM connector?

Repair the poor contact of ECM connector.

Inspection using “General Diagnostic Table” General Diagnostic Table > INSPECTION">

Fuel pump circuit

General description

Other materials:

Shift lock release using the shift lock release button
Perform the following procedure to release the shift lock. 1. Apply the parking brake and turn the ignition switch to the "LOCK"/"OFF" position. 2. Wrap the tip of a flat-head screwdriver with vinyl tape or a cloth and use it to remove the shift lock cover. The shift lock release button ...

Specification
VEHICLE DYNAMICS CONTROL (VDC) > General DescriptionSPECIFICATIONItemSpecification or identificationABS wheel speed sensorABS wheel speed sensor gap (for reference)Front0.77 — 1.43 mm (0.030 — 0.056 in)Rear0.44 — 1.76 mm (0.017 — 0.069 in)Identifications of harness (symbol)FrontRHZ1LHZ2Re ...

Display settings
Touch the tab to set display. Item Function Day/Night Mode The "Auto", "Day" or "Night" key can be selected on the pop-up screen. When the "Auto" key is selected, the screen changes to day or night mode depending on the position of the headlight swi ...