KEYLESS ACCESS WITH PUSH BUTTON START SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)
DTC B27A1 DRIVER SIDE EXTERNAL ANTENNA OPEN
DTC detecting condition:
When open circuit occurs in the harness between keyless access CM and driver’s side front door outer handle.
Trouble symptom:
Keyless access system does not function.
CAUTION:
For replacement procedure of keyless access CM, refer to the “REGISTRATION MANUAL FOR IMMOBILIZER” provided as a separate volume.
Wiring diagram:
Keyless access system Keyless Access System > WIRING DIAGRAM">
STEP | CHECK | YES | NO |
1.CHECK LAN SYSTEM.
Inspect LAN system. Basic Diagnostic Procedure > PROCEDURE">
Is LAN system normal?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A1 DRIVER SIDE EXTERNAL ANTENNA OPEN">Go to Step 2.
Perform the inspection according to the diagnosis for LAN system.
2.CHECK CONNECTOR.
1) Disconnect the keyless access CM connector.
2) Disconnect the front door outer handle connector.
Is the connector OK?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A1 DRIVER SIDE EXTERNAL ANTENNA OPEN">Go to Step 3.
Repair or replace the connector.
3.CHECK HARNESS (OPEN CIRCUIT).
Using a tester, measure the resistance between the keyless access CM connector and front door outer handle connector, and between front door outer handle connector, keyless access CM connector and chassis ground.
Connector & terminal
(B574) No. 12 — (D66) No. 6:
(B574) No. 13 — (D66) No. 3:
(D66) No. 2 — Chassis ground:
(B572) No. 11 — Chassis ground:
Is the resistance less than 1 ??
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A1 DRIVER SIDE EXTERNAL ANTENNA OPEN">Go to Step 4.
Repair or replace the open circuit of harness.
4.CHECK HARNESS (GROUND SHORT CIRCUIT).
Using a tester, measure the resistance between the keyless access CM connector and chassis ground.
Connector & terminal
(B574) No. 12 — Chassis ground:
(B574) No. 13 — Chassis ground:
Is the resistance 10 k? or more?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A1 DRIVER SIDE EXTERNAL ANTENNA OPEN">Go to Step 5.
Repair or replace the short circuit of the harness.
5.CHECK DTC.
1) Connect the keyless access CM connector.
2) Using the Subaru Select Monitor, clear the memory. Clear Memory Mode">
3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is DTC B27A1 displayed?
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B27A1 DRIVER SIDE EXTERNAL ANTENNA OPEN">Go to Step 6.
Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.
NOTE:
In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.
6.CHECK FRONT DOOR OUTER HANDLE.
1) Replace the driver’s side front door outer handle with the passenger’s front door outer handle. Front Outer Handle">
2) Using the Subaru Select Monitor, clear the memory. Clear Memory Mode">
3) Read the DTC using Subaru Select Monitor. Read Diagnostic Trouble Code (DTC)">
Is DTC B27A1 displayed?
Replace the keyless access CM. Keyless Access CM">
Replace the driver’s side front door outer handle. Front Outer Handle">
Touch screen operation
This system is operated mainly by the
keys on the screen.
When a screen key is touched, a beep
sounds. You can set the beep sound.
Refer to "Unit settings"
NOTE
If the system does not respond to
touching a screen key, move your
finger away from the screen and touch
it again.
Gra ...
Date screen
If you have set the date and time in the
selection screen, after the welcome
screen is displayed, the current date will
be displayed for a certain period of time. If
"On/Off setting" is set to "On" in the
"Maintenance settings", the date screen
will be displayed after the self-check
screen.
...
Dtc c2122 transmitter 2 no data
TIRE PRESSURE MONITORING SYSTEM (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC C2122 TRANSMITTER 2 NO DATANOTE:Refer to DTC C2124 for diagnostic procedure. Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC C2124 TRANSMITTER 4 NO DATA"> ...