Subaru Crosstrek manuals

Subaru Crosstrek Service Manual: Dtc b2329 rear radar axis alignment incomplete

Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)

DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE

DTC DETECTING CONDITION:

Axis adjustment of the radar sensor has failed.

(Forced termination of the Subaru Select Monitor, improper location of the target reflector, or deviation of the radar sensor due to impact.)

TROUBLE SYMPTOM:

All functions of BSD/RCTA stop.

Fail icon is displayed in the combination meter LCD display.

Failure-related notification is displayed for approx. two seconds on LCD display in the combination meter.

NOTE:

Check and replace the side that displayed the DTC.

STEPCHECKYESNO

1.CHECK REAR BUMPER.

Check the rear bumper.

Is there any fault? (Stickered, trace of repainting, etc.)

Replace or repair the bumper. Rear Bumper">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 2.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 2.

2.CHECK RADAR SENSOR BRACKET.

1) Remove the rear bumper. Rear Bumper">

2) Check the mounting bracket of the radar sensor as well as its installation position. Radar Sensor">

Is there any fault? (Visible damage, deformation, etc.)

Replace the mounting bracket of the radar sensor, or repair the installation position. Radar Sensor">
Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 3.

Diagnostic Procedure with Diagnostic Trouble Code (DTC) > DTC B2329 REAR RADAR AXIS ALIGNMENT INCOMPLETE">Go to Step 3.

3.ADJUSTMENT OF RADAR SENSOR AXIS.

1) Install the rear bumper.

2) Perform the adjustment of radar axis. Radar Sensor > ADJUSTMENT">

3) Perform the Inspection Mode. Inspection Mode">

Is DTC B2329 displayed? (Current malfunction)

Replace the radar sensor. Radar Sensor">

Even if DTC is displayed, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

NOTE:

In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

Dtc b2327 rear radar internal failure (internal electric circuit)
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2327 REAR RADAR INTERNAL FAILURE (INTERNAL ELECTRIC CIRCUIT)DTC DETECTING C ...

Dtc b2350 rear radar communication error between master and slave
Blind Spot Detection/Rear Cross Traffic Alert (DIAGNOSTICS) > Diagnostic Procedure with Diagnostic Trouble Code (DTC)DTC B2350 REAR RADAR COMMUNICATION ERROR BETWEEN MASTER AND SLAVEDTC DETECTING C ...

Other materials:

Disabling functions
By operating the access key If you have registered a PIN code for PIN Code Access, you can disable the keyless access function by operating the access key. For details about registering a PIN code, refer to "Registering a PIN code" 1. Open the driver's door. 2. Rotate the lock lever forwa ...

Preparation tool
FRONT SUSPENSION > General DescriptionPREPARATION TOOL1. SPECIAL TOOLILLUSTRATIONTOOL NUMBERDESCRIPTIONREMARKS927680000INSTALLER & REMOVER SETUsed for replacing the bushing front - front arm of front arm assembly.20299AG000REMOVER• Used for replacing the bushing rear - front arm of fron ...

SRS airbag (Supplemental Restraint System airbag)
*SRS: This stands for supplemental restraint system. This name is used because the airbag system supplements the vehicle's seatbelts. Your vehicle is equipped with a supplemental restraint system in addition to a lap/shoulder belt at each front seating position and each rear window-side sea ...

© 2016-2021 Copyright www.sucross.com